| Page 29 of 31 |
Appendix D. Driver Error Messages
The driver reports information and errors in the form of messages printed to the error log. Those messages marked with a * are only printed once even if they occur repeatedly.
| Error Message |
| Explanation |
| Carrier:#1 FYI. The |
| The length of the Map Descriptor used to expose driver |
| MapDesc called <%s> is too |
| statistics is too short. Set to at least 1000. This message may |
| short |
| be ignored§. |
| Carrier:#2 FYI. You could |
|
|
| have used a MapDesc called |
| This message is a prompt and may be ignored. Read |
| <%s> to expose diagnostic |
| Appendix C.1 for more information. |
| info. |
|
|
| Carrier:#3 Err. Illegal |
| Valid node numbers are in the range 1 to 15 inclusive. Read |
| Node_ID=%d Valid=1..15 |
| sections 4.3 or 5.3 for more information. § |
| Carrier:#4 FYI. Address has |
| You can ignore this message. The address parameter has no |
| no meaning. Best set to 1 |
| meaning in the configuration of this driver. Remove the |
| MapDesc=<%s> |
| parameter from the configuration or set its value to 1§ |
| Carrier:#5 Err. For write, set |
|
|
| length to 1. MapDesc=<%s> |
|
|
| Carrier:#6 FYI. Field Name |
| If the Field_Name parameter is left unspecified then the driver |
| Blank. Assumed |
| assumes you intend reading the whole table by filling in the |
| ©EVERYTHING©. |
| Field_Name with the keyword EVERYTHING. Suppress this |
| MapDesc=<%s> |
| message by specifying the Field_Name .§ |
| Carrier:#7 Err. Table name |
| Every Map Descriptor for this driver requires that you specify a |
|
| table name. Section 4.4.2 and Appendix A.1 provide additional | |
| required. MapDesc=<%s> |
| |
|
| information. § | |
| Carrier:#8 Err. Length |
| The length parameter must be set in the configuration file to a |
| required. MapDesc=<%s> |
| value greater than zero. Refer to Appendix A.3.§ |
| Carr:#9 FYI. Duplicate |
| You have specified a discrete state word in the configuration |
|
| file which is a duplicate of one already in the list. The driver | |
| state=<%s>. Value has been |
| |
|
| uses the new value, thus changing the values for the driver’s | |
| updated from=%d to=%d |
| |
|
| default discrete state words. You can ignore this message. | |
|
|
| |
| Carr:#10 Err. No space. |
| The driver has limited space to store discrete state keywords |
|
| added in the configuration file. The maximum is 150 words | |
| Driver rejects value |
| |
|
| including the driver’s defaults. Remove some of the keywords | |
| state=<%s> value=%d |
| |
|
| you have added to the configuration file. § | |
| Carr:#11 FYI. User added |
| You can ignore this message; it is for information only. Each |
|
| time a new discrete state word is added to the driver from the | |
| value state=<%s> value=%d |
| |
|
| configuration file, the driver reports the new word and its value. | |
|
|
| |
| Carr:#12 Err. Length too |
| The read table command resulted in more variables being |
|
| returned than you have reserved space for (with the length | |
| short to store all. MD=<%s> |
| |
|
| parameter). Increase the length parameter§. | |
| Carrier:#13 FYI. Diagnostic |
| These messages are for FieldServer engineers. If printed in |
| send error #1 response. |
| |
|
| the error log please call FieldServer support and report the | |
| Carrier:#14 FYI. Diagnostic |
| |
|
| message. | |
| cancelled slave response |
| |
|
|
|
§Correct the error by editing the configuration CSV file, downloading the corrected file to the FieldServer and then resetting the FieldServer.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408)