Manuals / ADTRAN / Communications / Cordless Telephone

ADTRAN 1202076L1#DC System Messages, Alarm Messages Network Interface NI, Message Description

Models: 1202076L2#DC 1202076L1#DC 1202076L1 1202076L2

1 123

Download 123 pages 47.38 Kb

Page 111

Appendix D

System Messages

This appendix lists and defines the alarm and status messages that ap- pear on the TSU 600 screen.

Alarm Messages: Network Interface (NI)

Message	Description

Red Alarm	NI unable to frame align with incoming signal

Yellow Alarm	Remote alarm indication (RAI) being received from
	far end

Blue Alarm	Unframed all ones (1s) (AIS) being received at NI

Loss of Signal	No signal detected at NI

61202076L1-1

TSU 600 User Manual

D-1

Image 111

ADTRAN 1202076L1#DC, 1202076L2#DC user manual System Messages, Alarm Messages Network Interface NI, Message Description

Contents

Part Numbers 1202076L1 1202076L1#DC 1202076L2 1202076L2#DC TSU TSU 600eTrademarks Year 2000 Compliance REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Table of Contents Configuration Menu OperationStatus Menu Loopback Tests Table of Contents TSU 600 Option Modules List of FiguresList of Figures List of Tables List of Tables Introduction TSU 600 OverviewProduct Description Standard Features in the TSU Module Name Description TSU Option ModulesTSU 600 Option Modules Option Module ArchitectureRouter, PBX, Video Conferencing Application TSU 600 Configuration ApplicationsDrop and Insert, Voice, and Router Application Drop and Insert, Voice, and Router Application Set UpAdtran Shipments Include InstallationUNPACK, INSPECT, Power UP Receipt InspectionExample Power ConnectionDC Powered Units Backup Power Supply 600e onlyStep Action Installing and Replacing the Power SupplyGrounding Instructions 1a.TSU 600 Rear Panel Identification of Rear Panel Layout1b.TSU 600 with DC Power Rear Panel 1c.TSU 600e Rear Panel 1d.TSU 600e with DC Power Rear Panel Chain Port Output TSU 600 InterfacesNetwork Test Interface Control Port InputOption Slot Arrangement 10BaseT Interface 600e onlySlot Power-up Testing SlotsSelf-Test Set User Passcode InitializationBoard level tests Unit level testsSet Control Port Chain-In PCChain In/Chain Out Normal Power-Up Procedure Front Panel OperationCSU Status LEDs If the LED is illuminated red , one or both If the LED is illuminated green , all installedModule Status LEDs System greenTSU 600 Front Panel Layout General Menu Operation Operation KeysExample of Basic Front Panel Menu Travel Selecting and Activating a Menu ItemEditing the Data Field Step Action ResultExit Any Menu Field Operation Or Display Display Only Data FieldsModule Slots, TSU Data Port IdentificationFront Panel Menu Structure Alternate Methods of Control Watch PRO Adtran PC ProgramWatch PRO/LAN Connection Watch PRO/EIA-232 Connection Connect the PC Com port to the Chain-In port onTelnet Connection Terminal Mode ConnectionOperation Complete Status Menu Status MenuNetwork Interface Performance Report Network Performance Reports NI Perf RptsNetwork Interface Errors NI Errors View History Active AlarmsClear Port Alarm Port StatusRemote Port PS Status 600e only Enet Status 600e onlyConfiguration Menu Configuration MenuNetwork NI Network NI Menu ItemsXmit PRM BIT Stuffing SET LBOInband LpbckNetwork Timing TSU 600 Clock SourcesDTE Timed Clock Source BR1TE Slot DTE TimingInternal Clock Source Internal TimingSecondary Clock Source Secondary TimingNormal CSU Normal CSU TimingUnit Menu CTL Auto Map Exchange Map Xchng MenuMAP In Use AB Menu OFFDS0 Map a and DS0 Map B Menu Copy a TempCreate Temp Apply Temp a Review MAPReview Temp Edit TempCreate Temp Selection Screen Port Configuration Port Config Configuration Menu Utility Menu Tree Utility MenuEnter Passcode from Other Menus Factory RestoreTime/Date Set PasscodeNo Passcode Desired Automatic Time-out FeatureUnit ID Change/Set a PasscodeEnet Address 600e only CMD ModeSoftware Revision Software Rev Port UtilityTest Menu Test MenuLoopback Tests Network TestsNetwork Interface Loopbacks Local LoopbckAnsi FDL LLB Remote LoopbkATT In-Band LLB Ansi FDL PLBTest Pattern Pattern DescriptionQrss Pattern Sync Pattern ResultBES SESRun Self-Test Port Tests Cancel TestsMain Menu Telnet/Terminal MenusDS0 Maps Configuration Menu Status, Config, Util, and Test Menu OptionsInitializing the Temp Map Step ActionEditing the Temp Map Applying the Temp MapReviewing Maps Remote Menu Access Management ConfigurationUnit Access Table Delete Unit Modify UnitDefault Unit Passcode Snmp Read CommunitySnmp Read/Write Community System Location Snmp Trap CommunitySystem Name System ContactQuit Session Flash DownloadTelnet/Terminal Menus Agent Appendix a Understanding SnmpBasic Components Network ManagerMessage CommandsSnmp Trap Configuration TSU 600 Snmp AccessSnmp MIB Files Snmp MIB Browser ConfigurationAppendix B Understanding TR-08 Table B-1. Alarm Conditions FelpOOF TR-08 Channel Number Port TR-08 DS0 Conversion TableTable B-2.TR-08 DS0 Conversion Table DS0Appendix B. Understanding TR-08 Network Connections WiringNetwork Pinouts NetworkControl In/Chain Chain-in ConnectionsTable C-2.Control In/Chain In Pinout Chain-Out Chain-out ConnectionsTable C-3. Chain-Out Pinout 10BaseT 600e only 10BaseT Connections10BaseT Ethernet Alarm Messages Network Interface NI System MessagesMessage Description Status Messages Network Interface NI Specifications Electrical SpecificationsT1/FT1 Interface Compatibility Management InterfacesOption Slot Interface Environmental Specifications Appendix E. Specifications Numerics Index600 Index-3 Index-4 61202076L1-1 Index-5 Index-6 61202076L1-1 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return