Control In/Chain, Chain-in Connections | ADTRAN 1202076L2 specs

Appendix C. Network Pinouts

Control In/Chain In

This is used as an EIA-232 port for connection to a computer or modem (Control-in) or to another TSU 600 or TSU 100 (chain-in). See Table C-2, Control In/Chain In Pinout for the pinout for the control-in/chain-in con- nector.

Chain-in Connections

The chain-in connections are as follows:

Connector Type	RJ-48
Part Number	AMP# 555164-2

Table C-2.Control In/Chain In Pinout

Pin	Name	Description

1	GND	Ground-connected to unit chassis

2	RTS	Request to send-flow control

3	RXDATA	Data received by the TSU 600

4	UNUSED

5	TXDATA	Data transmitted by the TSU 600

6,7	UNUSED

8	CTS	Clear to send -- flow control

C-2

TSU 600 User Manual

61202076L1-1

Image 108

ADTRAN 1202076L2#DC, 1202076L1#DC user manual Chain-in Connections, Table C-2.Control In/Chain In Pinout

Contents

TSU TSU 600e Part Numbers 1202076L1 1202076L1#DC 1202076L2 1202076L2#DC Trademarks Year 2000 Compliance REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Table of Contents Configuration Menu OperationStatus Menu Loopback Tests Table of Contents List of Figures TSU 600 Option Modules List of Figures List of Tables List of Tables Introduction TSU 600 OverviewProduct Description Standard Features in the TSU TSU Option Modules Module Name Description Option Module Architecture TSU 600 Option Modules TSU 600 Configuration Applications Router, PBX, Video Conferencing Application Drop and Insert, Voice, and Router Application Set Up Drop and Insert, Voice, and Router Application Installation UNPACK, INSPECT, Power UPReceipt Inspection Adtran Shipments Include Power Connection DC Powered UnitsBackup Power Supply 600e only Example Installing and Replacing the Power Supply Step Action Grounding Instructions Identification of Rear Panel Layout 1a.TSU 600 Rear Panel 1b.TSU 600 with DC Power Rear Panel 1c.TSU 600e Rear Panel 1d.TSU 600e with DC Power Rear Panel TSU 600 Interfaces Network Test InterfaceControl Port Input Chain Port Output Option Slot Arrangement 10BaseT Interface 600e onlySlot Power-up Testing SlotsSelf-Test Initialization Board level testsUnit level tests Set User Passcode Set Control Port Chain-In PCChain In/Chain Out Normal Power-Up Procedure Operation Front Panel CSU Status LEDs If the LED is illuminated green , all installed Module Status LEDsSystem green If the LED is illuminated red , one or both TSU 600 Front Panel Layout Operation Keys General Menu Operation Selecting and Activating a Menu Item Example of Basic Front Panel Menu Travel Step Action Result Editing the Data Field Display Only Data Fields Exit Any Menu Field Operation Or Display Data Port Identification Module Slots, TSU Front Panel Menu Structure Alternate Methods of Control Watch PRO Adtran PC ProgramWatch PRO/LAN Connection Connect the PC Com port to the Chain-In port on Watch PRO/EIA-232 Connection Terminal Mode Connection Telnet Connection Operation Status Menu Complete Status Menu Network Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms View History Clear Port Alarm Port StatusRemote Port Enet Status 600e only PS Status 600e only Configuration Menu Configuration Menu Network NI Network NI Menu ItemsXmit PRM SET LBO InbandLpbck BIT Stuffing TSU 600 Clock Sources Network Timing DTE Timing DTE Timed Clock Source BR1TE Slot Internal Timing Internal Clock Source Secondary Timing Secondary Clock Source Normal CSU Timing Normal CSU Unit Menu CTL Map Exchange Map Xchng Menu MAP In Use AB MenuOFF Auto DS0 Map a and DS0 Map B Menu Copy a TempCreate Temp Review MAP Review TempEdit Temp Apply Temp a Create Temp Selection Screen Port Configuration Port Config Configuration Menu Utility Menu Utility Menu Tree Factory Restore Time/DateSet Passcode Enter Passcode from Other Menus Automatic Time-out Feature Unit IDChange/Set a Passcode No Passcode Desired CMD Mode Software Revision Software RevPort Utility Enet Address 600e only Test Menu Test Menu Network Tests Loopback Tests Local Loopbck Network Interface Loopbacks Remote Loopbk ATT In-BandLLB Ansi FDL PLB Ansi FDL LLB Test Pattern Pattern DescriptionQrss Pattern Pattern Result BESSES Sync Run Self-Test Cancel Tests Port Tests Telnet/Terminal Menus Main Menu Status, Config, Util, and Test Menu Options DS0 Maps Configuration Menu Step Action Initializing the Temp Map Editing the Temp Map Applying the Temp MapReviewing Maps Remote Menu Access Management ConfigurationUnit Access Table Modify Unit Delete Unit Default Unit Passcode Snmp Read CommunitySnmp Read/Write Community Snmp Trap Community System NameSystem Contact System Location Flash Download Quit Session Telnet/Terminal Menus Appendix a Understanding Snmp Basic ComponentsNetwork Manager Agent Commands Message TSU 600 Snmp Access Snmp Trap Configuration Snmp MIB Browser Configuration Snmp MIB Files Appendix B Understanding TR-08 Table B-1. Alarm Conditions FelpOOF TR-08 DS0 Conversion Table Table B-2.TR-08 DS0 Conversion TableDS0 TR-08 Channel Number Port Appendix B. Understanding TR-08 Wiring Network PinoutsNetwork Network Connections Control In/Chain Chain-in ConnectionsTable C-2.Control In/Chain In Pinout Chain-Out Chain-out ConnectionsTable C-3. Chain-Out Pinout 10BaseT 600e only 10BaseT Connections10BaseT Ethernet Alarm Messages Network Interface NI System MessagesMessage Description Status Messages Network Interface NI Specifications Electrical SpecificationsT1/FT1 Interface Compatibility Management InterfacesOption Slot Interface Environmental Specifications Appendix E. Specifications Index Numerics 600 Index-3 Index-4 61202076L1-1 Index-5 Index-6 61202076L1-1 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return