TSU 600 Configuration Applications | ADTRAN 1202076L2#DC, 1202076L1

Chapter 1. Introduction

TSU 600 CONFIGURATION APPLICATIONS

The following examples illustrate possible configurations of TSU 600 applications.

Router, PBX, Video Conferencing Application

In this application, an Nx54/64 module provides a V.35 interface to a router. The PBX is interfaced to the TSU 600 with the DSX-1 module. An OCU DP module and OCU DP plug-on board provide two switched 56 circuits for video conferencing. The SLIP port or 10BaseT port (600e only) allows SNMP network management over the LAN. See Figure 1-2.

PBX

	TSU 600
	ROUTER
	SLIP or 10BaseT (600e only)
VIDEO
CONFERENCING	SNMP NETWORK
	MANAGEMENT WORKSTATION

Figure 1-2.Router, PBX, Video Conferencing Application Set Up

61202076L1-1

TSU 600 User Manual

1-5

Image 25

ADTRAN 1202076L2#DC, 1202076L1 user manual TSU 600 Configuration Applications, Router, PBX, Video Conferencing Application

Contents

Part Numbers 1202076L1 1202076L1#DC 1202076L2 1202076L2#DC TSU TSU 600e Trademarks Year 2000 Compliance REN/SOC FIC Usoc Page Canadian Emissions Requirements Canadian Equipment Limitations Affidavit Requirements for Connection To Digital Services Page Page Important Safety Instructions Warranty and Customer Service Table of Contents Operation Configuration MenuStatus Menu Loopback Tests Table of Contents TSU 600 Option Modules List of Figures List of Figures List of Tables List of Tables TSU 600 Overview IntroductionProduct Description Standard Features in the TSU Module Name Description TSU Option Modules TSU 600 Option Modules Option Module Architecture Router, PBX, Video Conferencing Application TSU 600 Configuration Applications Drop and Insert, Voice, and Router Application Drop and Insert, Voice, and Router Application Set Up UNPACK, INSPECT, Power UP InstallationReceipt Inspection Adtran Shipments Include DC Powered Units Power ConnectionBackup Power Supply 600e only Example Step Action Installing and Replacing the Power Supply Grounding Instructions 1a.TSU 600 Rear Panel Identification of Rear Panel Layout 1b.TSU 600 with DC Power Rear Panel 1c.TSU 600e Rear Panel 1d.TSU 600e with DC Power Rear Panel Network Test Interface TSU 600 InterfacesControl Port Input Chain Port Output 10BaseT Interface 600e only Option Slot ArrangementSlot Slots Power-up TestingSelf-Test Board level tests InitializationUnit level tests Set User Passcode Chain-In PC Set Control PortChain In/Chain Out Normal Power-Up Procedure Front Panel Operation CSU Status LEDs Module Status LEDs If the LED is illuminated green , all installedSystem green If the LED is illuminated red , one or both TSU 600 Front Panel Layout General Menu Operation Operation Keys Example of Basic Front Panel Menu Travel Selecting and Activating a Menu Item Editing the Data Field Step Action Result Exit Any Menu Field Operation Or Display Display Only Data Fields Module Slots, TSU Data Port Identification Front Panel Menu Structure Watch PRO Adtran PC Program Alternate Methods of ControlWatch PRO/LAN Connection Watch PRO/EIA-232 Connection Connect the PC Com port to the Chain-In port on Telnet Connection Terminal Mode Connection Operation Complete Status Menu Status Menu Network Interface Performance Report Network Performance Reports NI Perf Rpts Network Interface Errors NI Errors View History Active Alarms Port Status Clear Port AlarmRemote Port PS Status 600e only Enet Status 600e only Configuration Menu Configuration Menu Network NI Menu Items Network NIXmit PRM Inband SET LBOLpbck BIT Stuffing Network Timing TSU 600 Clock Sources DTE Timed Clock Source BR1TE Slot DTE Timing Internal Clock Source Internal Timing Secondary Clock Source Secondary Timing Normal CSU Normal CSU Timing Unit Menu CTL MAP In Use AB Menu Map Exchange Map Xchng MenuOFF Auto Copy a Temp DS0 Map a and DS0 Map B MenuCreate Temp Review Temp Review MAPEdit Temp Apply Temp a Create Temp Selection Screen Port Configuration Port Config Configuration Menu Utility Menu Tree Utility Menu Time/Date Factory RestoreSet Passcode Enter Passcode from Other Menus Unit ID Automatic Time-out FeatureChange/Set a Passcode No Passcode Desired Software Revision Software Rev CMD ModePort Utility Enet Address 600e only Test Menu Test Menu Loopback Tests Network Tests Network Interface Loopbacks Local Loopbck ATT In-Band Remote LoopbkLLB Ansi FDL PLB Ansi FDL LLB Pattern Description Test PatternQrss Pattern BES Pattern ResultSES Sync Run Self-Test Port Tests Cancel Tests Main Menu Telnet/Terminal Menus DS0 Maps Configuration Menu Status, Config, Util, and Test Menu Options Initializing the Temp Map Step Action Applying the Temp Map Editing the Temp MapReviewing Maps Management Configuration Remote Menu AccessUnit Access Table Delete Unit Modify Unit Snmp Read Community Default Unit PasscodeSnmp Read/Write Community System Name Snmp Trap CommunitySystem Contact System Location Quit Session Flash Download Telnet/Terminal Menus Basic Components Appendix a Understanding SnmpNetwork Manager Agent Message Commands Snmp Trap Configuration TSU 600 Snmp Access Snmp MIB Files Snmp MIB Browser Configuration Appendix B Understanding TR-08 Felp Table B-1. Alarm ConditionsOOF Table B-2.TR-08 DS0 Conversion Table TR-08 DS0 Conversion TableDS0 TR-08 Channel Number Port Appendix B. Understanding TR-08 Network Pinouts WiringNetwork Network Connections Chain-in Connections Control In/ChainTable C-2.Control In/Chain In Pinout Chain-out Connections Chain-OutTable C-3. Chain-Out Pinout 10BaseT Connections 10BaseT 600e only10BaseT Ethernet System Messages Alarm Messages Network Interface NIMessage Description Status Messages Network Interface NI Electrical Specifications SpecificationsT1/FT1 Interface Management Interfaces CompatibilityOption Slot Interface Environmental Specifications Appendix E. Specifications Numerics Index 600 Index-3 Index-4 61202076L1-1 Index-5 Index-6 61202076L1-1 Post-Sale Support Presales Inquiries and Applications SupportRepair and Return