Maxtor 4320 manual Before You Begin

Page 26

INSTALLATION

1 Before You Begin

IMPORTANT – PLEASE READ!

Please read this Installation Sheet completely before installing the Maxtor hard drive. It gives general information for installing a Maxtor hard drive in a typical computer system.

If you don’t understand the installation steps, have a qualified computer technician install the hard drive.

Handling Precautions

P(

H H

H

Allow the hard drive to reach room temperature BEFORE installing it in your computer system.

Hard drives are sensitive to electrostatic discharge (ESD) damage.

Handle the drive by its sides. DO NOT touch the printed circuit board assembly.

NEVER drop, jar, or bump the drive.

DON’T connect/disconnect any drive cables when the power is on.

DON’T use any low-level formatting software on this drive.

System Requirements

◆IDE/AT interface

◆486 processor or higher

◆Operating System Requirements

•For drives less than or equal to 8.4 GB: DOS 5.0 or higher

•For drives larger than 8.4 GB:

√Installing as Boot drive (Primary Master) requires full installation set of Windows 95 or higher (not upgrade).

√Installing as non-Boot drive (Primary Slave, Secondary Master or Slave) requires that Windows 95 or higher be installed on the Boot drive.

Tools for Installation

The following tools are needed to complete the installation of your Maxtor hard drive:

◆ A small Phillips head screw driver

◆ Your computer user’s manual

◆ Small needle-nose pliers or

◆ Operating system software

tweezers

 

Drive Identification Information

Copy the following information from the label on the top cover of the Maxtor hard drive for future reference:

Model Number _____________________Serial Number __________________

Cylinders ______________ Heads _____________ Sectors _______________

Capacity Barriers

Due to operating system limitations, DOS cannot access the full capacity of drives larger than 8.4 GB. The Microsoft Windows 95 operating system or equivalent (full installation), NOT a Windows 95 upgrade from DOS (Windows 3.1 or 3.11), is required to obtain the full capacity of any hard drive larger than 8.4 GB.

Protecting Your Existing Data

Periodicbackupofimportantdataisalwaysagoodidea.Wheneveryourcomputerison,thereisthepotentialforlosingdataonyourharddrive.Thisisespeciallytruewhenrunning disk utilities or any software that directly manipulates your files. Maxtor recommends that you make a backup copy of the files on any existing hard drives. If required, this datamaythenbecopiedtotheMaxtorharddriveafterithasbeeninstalledinyourcomputer.Refertoyourcomputeruser’smanualfordetaileddatabackupinstructions.

4 – 4

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HA RD Drive Produc T MA Nual DiamondMax Revisions Manual No Before You Begin U T I O NContents Product Specifications Handling and InstallationAT Interface Description Host Software InterfaceGlossary Interface CommandsService and Support Figures Manual Organization IntroductionMaxtor Corporation AbbreviationsKey Words Signal ConventionsConventions NumberingDiamondMax 4320 Key Features Product DescriptionProduct Features Functional / InterfaceDefect Management Zone DMZ On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Software ECC CorrectionBuffer Segmentation Read-Ahead ModeCache Management Automatic Write Reallocation AWRMajor HDA Components Cylinder Limitation Subsystem ConfigurationJumper Location/Configuration Dual Drive SupportPerformance Specifications Product SpecificationsDrive Configuration Models and CapacitiesPhysical Dimensions Parameter Standard MetricEPA Energy Star Compliance Power Requirements AveragePower Mode Definitions Environmental LimitsReliability Specifications Shock and VibrationCanadian Emissions Statement Safety Regulatory ComplianceRadiated Electromagnetic Field Emissions EMC Compliance Pre-formatted Drive Handling and Installation Hard Drive Handling Precautions Important NoticeUnpacking and Inspection Multi-pack Shipping ContainerRepacking Physical InstallationRecommended Mounting Configuration Before You Begin General Requirements Mounting Drive in System Attaching Interface Power Cables System Setup Hard Drive Preparation System Hangs During Boot Pin Description Summary Interface ConnectorAT Interface Description PINPIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Mode MIN MAX Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Host Software Interface Error RegisterFeatures Register Task File RegistersCylinder Number Registers Sector Count RegisterSector Number Register Device/Head RegisterCommand Register Summary Command Name Command Code Parameters UsedTimer Value TIME-OUT Period Device Control Register Control Diagnostic RegistersAlternate Status Register Digital Input RegisterInterrupt Handling Reset and Interrupt HandlingReset Handling Interface Commands Set Feature CommandsRead Verify Sectors Read CommandsRead Sectors Read DMA Read MultipleWrite Sectors Write CommandsSet Multiple Mode Write Verify SectorsWrite Multiple Write DMAValue Description Set Feature CommandsSet Features Mode Power Mode Commands Sleep Mode Identify Drive Initialization CommandsWord Content Description 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Error Code Description Seek, Format and Diagnostic CommandsExecute Drive Diagnostic Format TrackA.R.T. Command Set Execute S.M.A.R.TNo Quibble Service Service and SupportService Policy SupportInternet MaxFax ServiceCustomer Service Access Time GlossaryCylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media
Top Page Image Contents