Maxtor 4320 manual Logical Block Addressing, Defect Management Zone DMZ, Software ECC Correction

Page 14

PRODUCTDESCRIPTION

Logical Block Addressing

The Logical Block Address (LBA) mode can only be utilized in systems that support this form of translation. The cylinder, head and sector geometry of the drive, as presented to the host, differs from the actual physical geometry. The host AT computer may access a drive of set parameters: number of cylinders, heads and sectors per track, plus cylinder, head and sector addresses. However, the drive can’t use these host parameters directly because of zoned recording techniques. The drive translates the host parameters to a set of logical internal addresses for data access.

The host drive geometry parameters are mapped into an LBA based on this formula:

LBA

=

(HSCA - 1) + HHDA x HSPT + HNHD x HSPT x HCYA

(1)

 

=

(HSCA - 1) + HSPT x (HHDA + HNHD x HCYA)

(2)

where

HSCA = Host Sector Address, HHDA = Host Head Address

 

 

HCYA = Host Cylinder Address, HNHD = Host Number of Heads

 

 

HSPT = Host Sectors per Track

 

The LBA is checked for violating the drive capacity. If it does not, the LBA is converted to physical drive cylinder, head and sector values. The physical address is then used to access or store the data on the disk and for other drive related operations.

Defect Management Zone (DMZ)

Each drive model has a fixed number of spare sectors per drive, all of which are located at the end of the drive. Upon detection of a bad sector that has been reassigned, the next sequential sector is used.

For example, if sector 3 is flagged, data that would have been stored there is “pushed down” and recorded in sector 4. Sector 4 then effectively becomes sector 3, as sequential sectors are “pushed down” across the entire drive. The first spare sector makes up for the loss of sector 3, and so maintains the sequential order of data. This push down method assures maximum performance.

On-the-Fly Hardware Error Correction Code (ECC)

33 bits, single burst, guaranteed

Software ECC Correction

81 bits, single burst, guaranteed

33 bits, double bursts, guaranteed

Automatic Park and Lock Operation

Immediately following power down, dynamic braking of the spinning disks delays momentarily allowing the read/write heads to move to an inner mechanical stop. A small fixed magnet holds the rotary actuator in place as the disk spins down. The rotary actuator is released only when power is again applied.

2 – 3

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HA RD Drive Produc T MA Nual DiamondMax Revisions Manual No Before You Begin U T I O NContents Product Specifications Handling and InstallationAT Interface Description Host Software InterfaceGlossary Interface CommandsService and Support Figures Manual Organization IntroductionMaxtor Corporation AbbreviationsKey Words Signal ConventionsConventions NumberingDiamondMax 4320 Key Features Product DescriptionProduct Features Functional / InterfaceDefect Management Zone DMZ On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Software ECC CorrectionBuffer Segmentation Read-Ahead ModeCache Management Automatic Write Reallocation AWRMajor HDA Components Cylinder Limitation Subsystem ConfigurationJumper Location/Configuration Dual Drive SupportPerformance Specifications Product SpecificationsDrive Configuration Models and CapacitiesPhysical Dimensions Parameter Standard MetricEPA Energy Star Compliance Power Requirements AveragePower Mode Definitions Environmental LimitsReliability Specifications Shock and VibrationCanadian Emissions Statement Safety Regulatory ComplianceRadiated Electromagnetic Field Emissions EMC Compliance Pre-formatted Drive Handling and InstallationHard Drive Handling Precautions Important NoticeUnpacking and Inspection Multi-pack Shipping ContainerRepacking Physical InstallationRecommended Mounting Configuration Before You Begin General Requirements Mounting Drive in System Attaching Interface Power Cables System Setup Hard Drive Preparation System Hangs During Boot Pin Description Summary Interface ConnectorAT Interface Description PINPIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Mode MIN MAX Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Host Software Interface Error RegisterFeatures Register Task File RegistersCylinder Number Registers Sector Count RegisterSector Number Register Device/Head RegisterCommand Register Summary Command Name Command Code Parameters UsedTimer Value TIME-OUT Period Device Control Register Control Diagnostic RegistersAlternate Status Register Digital Input RegisterInterrupt Handling Reset and Interrupt HandlingReset Handling Interface Commands Set Feature CommandsRead Verify Sectors Read CommandsRead Sectors Read DMA Read MultipleWrite Sectors Write CommandsSet Multiple Mode Write Verify SectorsWrite Multiple Write DMAValue Description Set Feature CommandsSet Features Mode Power Mode Commands Sleep Mode Identify Drive Initialization CommandsWord Content Description 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Error Code Description Seek, Format and Diagnostic CommandsExecute Drive Diagnostic Format TrackA.R.T. Command Set Execute S.M.A.R.TNo Quibble Service Service and SupportService Policy SupportInternet MaxFax ServiceCustomer Service Access Time GlossaryCylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media

4320 specifications

The Maxtor 4320 is a notable entry in the realm of hard disk drives, widely recognized for its reliability and performance in data storage. Released in the early 2000s, it quickly gained traction among both consumers and professionals looking for efficient solutions for their data management needs.

At the core of the Maxtor 4320 is its impressive storage capacity. With a capacity of 20GB, it was considered substantial at the time, making it ideal for storing a variety of files, from documents to multimedia content. This drive provided users with ample space to expand their digital footprint without the constant worry of running out of space.

One of the standout features of the Maxtor 4320 is its data transfer rate. Operating at a speed of 5400 RPM, it offered a balanced performance that suited casual users and most business applications. The drive utilized an IDE interface, ensuring compatibility with a wide range of motherboards and systems, allowing for easy integration into both desktop and laptop computers.

The Maxtor 4320 is characterized by its durability. Engineered with robust materials and a well-designed casing, it was built to withstand regular use. This durability became a significant selling point, as data integrity and safety are paramount in any storage solution. Users could rely on the Maxtor 4320 to protect their important data against the wear and tear associated with daily operations.

In terms of technologies, the Maxtor 4320 featured advanced error correction algorithms, which ensured that data retrieval was not only fast but also reliable. This was particularly important at a time when data integrity was becoming increasingly crucial for personal and corporate users alike.

Additionally, the drive's low power consumption was a key consideration for eco-conscious consumers. It allowed for extended use without excessively draining power, contributing to lower energy bills and a smaller carbon footprint. This feature made the Maxtor 4320 an attractive option for users looking to balance performance with energy efficiency.

In conclusion, the Maxtor 4320 combined reliability, performance, and durability to become a popular choice in the hard disk drive market of the early 2000s. Its large storage capacity, reasonable speed, and energy efficiency catered to a wide range of users, from home consumers to small businesses. The legacy of the Maxtor 4320 continues to influence current storage solutions as it laid the groundwork for advancements in hard disk technology.
Top Page Image Contents