FieldServer FS-8700-103 instruction manual Alarm Reset ALL Malfunctions Clear, Example

Page 16

FS-8700-103_ATMI_TGM_Serial Manual

Page 16 of 28

Appendix B. Advanced Topics

Appendix B.1. How Malfunctions are determined and stored

•The notes below describe how the driver parses incident reports obtained by the QIR poll.

•The driver starts at the end of the report and works its way to the top, line by line.

•Each line is inspected to see if it contains either of the following strings

“ALARM RESET"

"ALL MALFUNCTIONS CLEAR”

•If either is reported then the driver sets all the array elements to zero except those corresponding to lines of the report appearing after (and hence later in time) one of the above lines that indicates that malfunctions be set, in which case those particular malfunctions will be reported as 1’s in the Data Array.

•When either one of these two events is found the driver stops parsing the report as all prior lines predate the clear event.

•Each line is inspected for the string “MALFUN”. If it is found then ‘Event’ field in the report is inspected and the description is extracted and compared to the malfunction list provided in Appendix A.2. If a match is found the driver uses the offset value and sets the corresponding element in the Data Array to 1.

•If the string “MAFUN” is not found then the description found in the ‘Event’ field of the report is used to look up a ‘Return to Normal’ event in the table provided in Appendix A.2. If a match is found then the corresponding offset in the Data Array is set to zero.

•If the description is not recognized then it it is ignored.

Example

Only the Malfunction ‘COUS SENSOR TIMEOUT’ would have its Data Array element set to

1.All others will be set to zero. The reason is that all events above the ‘ALARM RESET’ line are considered to be prior to the reset and are thus cleared when the driver sets all the Data Array elements to zero. The timeout event occurs later and hence its malfunction is set.

MALFUN

POWER FAILURE

00:00 00

00

MALFUN

POWER RESTORED

10:29 16 FEB 04

TGM IN DEBUG MODE

10:29 16 FEB 04

MALFUN

FAILED FLAME TEST

10:29 16

FEB 04

MALFUN

ALARM RESET

10:29 16

FEB 04

COUS SENSOR TIMEOUT

10:29 16

FEB 04

 

 

 

 

When the driver uses the lookup table to see if it recognizes the event description then it compares the strings looking for an exact match. If no exact match is made then the driver uses a so-called ‘soundex’ function to see if the strings are very similar, if they are then they are considered to be matched. If a similar match is made the driver reports this in the error log.

16 T02> TGM:#21 FYI. Malfunction. Dont recognize <POWER FAILED>

17 T02>

But sounds like <POWER FAILURE>.

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com

Page 15 Page 17
Image 16
Page 15 Page 17
Contents FS-8700-103 ATMI-TGM Serial Driver Table of Contents Max Nodes Supported FieldServer Mode Comments Atmi TGM Serial Driver DescriptionFS-8700-103ATMITGMSerial Manual Client Only 1 Server Node Allowed PER PortRequired 3rd Party Configuration FieldServer Technologies DescriptionHardware Connections Malfun Printer OFF Line Hardware Connection Tips / HintsMalfun Remote OFF Line Configuring the FieldServer as a Atmi TGM Serial Client Data Arrays/DescriptorsSection Title Column Title Function Legal ValuesClient Side Node Descriptors Client Side Connection DescriptionsNone Driver Related Map Descriptor Parameters Timing ParametersRDBC, ARS Column Function Legal Values TitleMap Descriptor Example #1 Calr Report CalrMap Descriptor Example #2 QLA Report Map Descriptor Example #3 QIR Report Malfunctions QIRGas Name Index Value None ASH3CH4 CH4AC CL2 DET GEH4 H2AC H2S H2SE HCL N2O NF3 NH3 PH3 Pocl POCL3 SihxAppendix A.2. Malfunction Table Offset Malfunction Return to NormalEngineering Units Index Value Appendix A.3. Gas Concentration Engineering UnitsARU PPM PPB LEL PCT Alarm Reset ALL Malfunctions Clear Contents Appendix B.2. How Gas Data is StoredData Array specified by the DataArrayName Data Array specified by the DABitNameAppendix B.4. Adding / Modifying Hard Coded Gas Names PPM TGMAppendix B.5. Adding / Modifying Malfunction Strings C2H5OH TGMDisk Nearly Full TGM Disk is Full TGMDisk no Longer Full TGM Appendix B.6. Adding / Modifying ‘Return to Normal’ StringsDisk not Full TGM Appendix B.8. Synchronizing Malfunctions FS-8700-103ATMITGMSerial ManualPage 22 Appendix C. Driver Error MessagesMessage FS-8700-103ATMITGMSerial Manual Message FYI#21 UINT16 Appendix C.1. Exposing Driver Operating StatisticsStat Relative Offset FS-8700-103ATMITGMSerial Manual Word baudRate = This page Intentionally Left Blank

FS-8700-103 specifications

The FieldServer FS-8700-103 is an advanced gateway solution designed to facilitate seamless communication between different building automation systems and devices. Its primary function is to provide interoperability among various protocols and devices, which is increasingly important in modern facility management. The FS-8700-103 alleviates common challenges faced by system integrators, allowing for easy integration and operation of diverse systems from multiple manufacturers.

One of the standout features of the FieldServer FS-8700-103 is its support for multiple communication protocols. These include Modbus, BACnet, LonWorks, and SNMP, among others. This versatility allows the FS-8700-103 to serve as a bridge between legacy systems and newer technologies, thus extending the useful life of existing infrastructure while enabling the addition of advanced system capabilities.

The FS-8700-103 is equipped with numerous ports, including Ethernet connections, which support both wired and wireless communications. This flexibility ensures that the gateway can fit into various network configurations and adapt to different deployment scenarios. In addition, its robust design guarantees reliable performance even in demanding environments, making it suitable for use in commercial, industrial, and residential applications.

Another key characteristic of the FS-8700-103 is its intuitive web-based interface. This interface simplifies the configuration process, allowing users to set up the system with minimal technical expertise. The built-in diagnostic tools provide real-time monitoring and troubleshooting capabilities, enabling operators to quickly identify and address issues, thus reducing downtime and enhancing operational efficiency.

Security is also a notable feature of the FS-8700-103. With increasing concerns regarding cybersecurity in building management systems, this gateway incorporates advanced security protocols to protect data integrity and privacy. This ensures that sensitive information remains safeguarded against unauthorized access.

In summary, the FieldServer FS-8700-103 stands out as a reliable and versatile solution for achieving interoperability in building automation systems. Its support for multiple protocols, robust connectivity options, user-friendly interface, and strong security measures make it a valuable asset for any organization looking to streamline operations and enhance the effectiveness of their automation systems. With the FS-8700-103, organizations can move towards a more integrated and efficient future in facility management.
Top Page Image Contents