ISonic K8NF4G-SATA2 manual Advanced Screen, CPU Configuration, Overclock Mode, CPU Frequency MHz

Page 25

3.3Advanced Screen

In this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security

Exit

Advanced Settings

WARNING : Setting wrong values in below sections may cause system to malfunction.

CPU Configuration

Chipset Configuration

ACPI Configuration

IDE Configuration

PCIPnP Configuration

Floppy Configuration

SuperIO Configuration

USB Configuration

Options for CPU

 

Select Screen

 

Select Item

Enter

Go to Sub Screen

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

Setting wrong values in this section may cause the system to malfunction.

3.3.1 CPU Configuration

BIOS SETUP UTILITY

Advanced

CPU Configuration

Overclock Mode

[Auto]

CPU Frequency (MHz)

[200]

PCIE Frequency (MHz)

[100]

Boot Failure Guard

[Enabled]

CPU Spread Spectrum

[Center Spread]

PCIE Spread Spectrum

[Enabled]

SATA Spread Spectrum

[Enabled]

HT Spread Spectrum

[Center Spread]

Cool' n' Quiet

[Enabled]

Processor Maximum Multiplier

x11

Processor Maximum Voltage

1.550 V

Multiplier/Voltage Change

[Auto]

Memory Clock

[Auto]

Flexibility Option

[Disabled]

Bank Interleaving

[Auto]

Burst Length

[4 Beats]

CAS Latency (CL)

[Auto]

TRCD

[Auto]

TRAS

[Auto]

If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup.

 

Select Screen

 

Select Item

+-

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

Overclock Mode

Use this to select Overclock Mode. The default value is [Auto]. Cnfiguration options: [Auto], [CPU, PCIE, Sync.] and [CPU, PCIE, Async.].

CPU Frequency (MHz)

Use this option to adjust CPU frequency. The range is from 140MHz to 300MHz. The default value is [200].

2 5

Page 24 Page 26
Image 25
Page 24 Page 26
Contents K8NF4G-SATA2 Disclaimer Copyright NoticeContents Appendix AMD’s Cool ‘n’ QuietTM Technology Software SupportIntroduction Package ContentsSpecifications Support CD Bios FeatureHardware MonitorPage RoHS Motherboard LayoutTable for Audio Output Connection HD 8CH I/OPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationNotch break Installation of Memory Modules DimmEasy Multi Monitor Feature Installing an expansion cardExpansion Slots PCI Express Slots, PCI Slots and Hdmr SlotOnboard Headers and Connectors Jumpers SetupSetting IDE1 Infrared Module Header System Panel Header Western Digital Sataii Hard Disk Setup GuidePage Use RAID Installation Guide to set RAID configuration Set Up BiosMake a Sata / Sataii Driver Diskette Untied Overclocking Technology Bios Menu Bar Main Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOverclock Mode CPU ConfigurationAdvanced Screen CPU Frequency MHzPcie Frequency MHz Boot Failure GuardCPU Spread Spectrum Pcie Spread SpectrumProcessor Voltage Processor MultiplierMemory Clock Flexibility OptionChipset Configuration Acpi Configuration Sataii Operation Mode IDE ConfigurationIDE Device Configuration OnBoard IDE ControllerPIO Mode LBA/Large ModeDMA Mode Block Multi-Sector TransferPCI Latency Timer PCIPnP ConfigurationA.R.T 32Bit Data TransferSuper IO Configuration Floppy ConfigurationOnBoard Floppy Controller Serial Port AddressECP Mode DMA Channel Parallel Port ModeParallel Port Address EPP VersionHardware Health Event Monitoring Screen USB ConfigurationUSB Controller USB 2.0 SupportBoot Settings Configuration Boot ScreenBoot From Network Boot Up Num-LockChange Supervisor Password Main Advanced Monitor BootSecurity Screen Exit Screen Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitSupport CD Information Install Operating SystemRunning The Support CD Drivers MenuAppendix
Top Page Image Contents