I-O Display Systems Basic I/O Product manual 8Vol.2

	Available I/O Modules		Introduction 1
ANALOG INPUTS, 12 BIT		ANALOG OUTPUTS, 12 BIT
Frequency		Voltage
I F10K-B	Input 300Hz-10KHz	OV1	Output 0-1V, self-sourcing
IF2.5K-L	Input 0-2.5KHz	OV5	Output 0-5V, self-sourcing
IF5K-l	Input 0-5KHz	OV10	Output 0-10V, self-sourcing
IF10K-L	Input 0-10KHz	Current
Voltage		OI420	Output 4-20mA, self-sourcing To 275
IV25M	Input 0-25mV		Ohm load
IV50M	Input 0-50mV	DIGITAL	INPUTS
IV100M	Input 0-100mV	AC
IV1	Input 0-1V	IAC5	Input 90-140Vac
IV5	Input 0-5V	IAC5A	Input 180-280Vac
IV5B	Input Bipolar +/-5V	DC
IV10	Input 0-10V	IDC5D	Input 3-32Vdc Fast, >500Hz
IV10B	Input Bipolar +/-10V	IDC5S *	Input Dry Contact Sense, Built-in Isolated
			Voltage Source
IVAC	Input 28-140Vac	IDC5NP	Input 10-32 Vdc, 15-32Vac Non-
IVAC-A	Input 56-280Vac		Polarized.
Current		DIGITAL	OUTPUTS
II420	Input 4-20mAdc	AC
IIAC5	Input 0-5Aac	OAC5	Output 12-140Vac, 3.5A
Thermocouple		OAC5A	Output 24-280Vac, N.C.(Normally Closed)
ITCE	Type E 0 To 435° C	OAC5J	Output 20-280Vac, 6.0A
ITCJ	Type J 0 To 700° C	DC
ITCJ-1	Type J -80 To 750 °C	ODC5	Output 5-60Vdc, 3.5A
ITCK	Type K -100 To 924° C	ODC5A	Output 4-200Vdc, 1.0A
ITCK-1	Type K -110 To 1250 °C	ODC5R	Electro-Mechanical 0.5A Relay Form A,
			Normally )
ITCR	Type R 0 To 960° C	IDC5Z*	Input +/-200mV, 0-10KHz Digital**
ITCR-1	Type R 0 To 1760 °C	SPS-1*	Sensor Power Supply 18-24 Vdc, 30mA
ITCS	Type S 0 To 1034° C	TI01	Digital Input/ Output Test Module with
ITCS-1	Type S 0 To 1760° C		Field Switch and LED
ITCT	Type T -200 To 224 °C
ITCT-1	Type T -120 To 400° C
ITCT-2	Type T 0 To 150 °C
SPECIAL PURPOSE		SUPPORT	PRODUCTS
RTD		Fuses
ITR10	10 Ohm Cu -55 To 150 °C	FM-06	Fuse assembly, 0.062A 100 mA for
			modules marked with an *
ITR100	100 Ohm Pt -55 To 350 °C	FM-1	Fuse assembly, 1.0A
ITR100-1	100 Ohm Pt 0 To 100 C	FM-3	Fuse assembly , 3.0A
Type 590 Temperature	Sensor	FM-5	Fuse assembly, 5.0A
ITP590	-188.4 To 150 °C
ITP590-1	-50.0 To 150 °C

*When selecting a power supply for the system assume 25mA for standard digital modules and 100mA for modules marked with an *

**The IDC5Z module is used for low-level signals and will pass signals at the rate of 10kHz The BASIC I/O AD however, is limited by communications baudrate.

1-8(Vol.2)