I-O Display Systems Basic I/O Product manual Basic I/O setup

Page 30

Setup & Installation 2

BASIC I/O setup:

BASIC I/O setup is accomplished with a sequential display and pushbutton. Below is a diagram of the location of these components.:

Figure 2-9 BASIC I/O Connectors, Switches and Indicators.

Unit type (digital or analog), Unit address, baud rate, and 2 or 4 pass protocols are all pushbutton configurable and appear on the sequential display. After line power application and the performance of system diagnostics, there is a five second period during which these setup values any be changed. Changed values are automatically saved on a non-volatile

EEPROM.

2-13(Vol.1)

Image 30

Contents Page Basic I/O Product Family Page Vol.1 Table of Contents Vol Table of Contents Basic I/O Basic I/OAnalog Inputs Analog input instruction types areAnalog Outputs Digital Inputs Digital Outputs System Throughput Throughput Tables7Vol.1 Communication Protocol Analog INPUTS, 12 BIT Analog OUTPUTS, 12 BIT Diagnostics Physical CharacteristicsProduct Test Basic I/O Models12Vol.1 Setup & Installation MountingPower Wiring +5V GNDCommunicating with the Basic I/O RS-485 can only be multidrop RepeatRS-422 RS-485RS-485 Programming Communication Wiring Network load V.S. Noise suppression Network Bias Resistor LocationsRS-422 Host to Basic I/O wiring RS-422 Host to Basic I/OBasic I/O to Basic I/O RS-422 Multidrop or Repeater RS-422 Basic I/O-To-BASIC I/O multidropRS-485 Host to Basic I/O RS-485 To-BASIC I/OBasic I/O to Basic I/O RS-485 Multidrop only RS-485 Basic I/O to Basic I/O MultidropBasic I/O setup Basic I/O Connectors, Switches and IndicatorsAnalog/ Digital AddressesBaud Rates Protocol Handshake Types L2 Multidrop Network Type SwitchL1 Repeater L3 Last UnitSetup via Pushbutton U1=00 H096 L3 P2Communication verification Other error codes Hardware error codesError Code Sensor/ Actuator I/O wiring10 AC Current and Voltage Wiring Analog Inputs11 Analog Voltage and Current input Wiring 13 Analog Voltage and Current Output Wiring Analog outputs14 Digital Input Wiring Digital Inputs15 Digital Output Wiring Digital OutputsVol.1 Index Analog OutputsPage Basic I/O AD Vol Table of Contents Basic I/O AD to Basic I/O AD RS-422 Introduction CapacityProduct Test Signal compatibility Protocol Compatibility Gain/ Slope TemperatureOffsets Range LimitsPulse widths DelayedDigital inputs Read Pulse countingSquarewave Pulse GeneratorExtended capabilities Position Basic I/O AD SpecificationsOrdering Information BIO8AD/L8Vol.2 Installation InstallationPower Wiring Designing the Network MultidropRS-422 RS-485 Programming Communication Wiring Network Bias resistor locations Network Type Switches Basic I/O AD Connectors, Switches and IndicatorsLast Unit Communications Wiring RS-422 Host to Basic I/O ADRS-485 Host to Basic I/O AD RS-485 To-BASIC I/O ADBasic I/O AD to Basic I/O AD RS-422 RS-422 Basic I/O AD-To-BASIC I/O ADBasic I/O AD to Basic I/O AD RS-485 RS-485 Basic I/O AD to Basic I/O ADInstalling the I/O modules Basic I/O AD Module Placement WorksheetModule Wiring Analog Inputs 11 AC current and voltage wiring12 Analog Voltage, frequency and Current input Wiring 14 Analog Voltage and Current Output Wiring 15 Digital Input Wiring 16 Digital output wiring Offset Mode SetupChassis Setup Function addressesVariable Mode Baud Rates Changing Setup Parameters Via Pushbutton Communication Verification Hardware error codes Vol.2 Index Vol.2 Index