HotBrick manual Rear Panel VPN 800/2 Firewall Router, Default Settings, AC power socket

Page 10

HotBrick Network Solutions

Rear Panel VPN 800/2 Firewall Router

Figure:1-2: Rear Panel VPN 800/2 Firewall Router

AC power socket

Connect the supplied power here.

Default Settings

When the VPN 800/2 Firewall Router has finished booting, all configuration settings will be set to the factory defaults, including:

•IP Address set to its default value of 192.168.1.1, with a Network Mask of 255.255.255.0

•DHCP Server is enabled

•User Name: admin

•Password cleared (no password)

TFTP Download

This setting should be used only if your VPN 800/2 Firewall Router is unusable, and you wish to restore it by downloading new firmware. Follow this procedure:

1.Power On the VPN 800/2 Firewall Router.

2.Use the supplied Windows utility or a TFTP client program applies the new firmware. If using the supplied Windows TFTP program, the screen will look like the following example.

Figure 1-3: Windows TFTP utility VPN F 800/2 Firewall Router

•Enter the name of the firmware upgrade file on your PC, or click the "Browse" button to locate the file.

•Enter the LAN IP address of the VPN 800/2 Firewall Router in the "Server IP" field.

•Click "Download" to send the file to the VPN 800/2 Firewall Router.

3.When downloading is finished. It should then work normally, using the default settings.

Page 6

Image 10

Contents Dual WAN Firewall Router VPN 800 User’s Guide Page Table of Contents Advanced LAN Configuration ………………………………………………………………...67 Existing Dhcp Server ………………………………………………………………………………...67Introduction Internet FeaturesThis gives twice the bandwidth of a single modem PPPoE Session Management Other Features Port Switching HubPackage Contents Physical DetailsLED Action Condition AC power socket Default SettingsRear Panel VPN 800/2 Firewall Router Page Configuring the VPN 800/2 Firewall Router for your LAN Basic SetupProcedure OverviewNo Response? IP Address Settings LAN & DhcpSubnet Mask Dhcp Server ConfigurationLAN Any IP Setup Dhcp IP AddressHotBrick Network Solutions Settings Primary Setup Connection ModeAddress Info ConnectionType PPPoE / PptpInternet Access Configure PCs on your LANTCP/IP Settings OverviewMacintosh Clients Accessing AOLLinux Clients Fixed IP Address Advanced Port Setup Port OptionsTransparent Bridge Settings Port OptionsConnection Options OptionLoad Balance Load BalanceStatistics Settings Load BalanceLoad Balance InterfaceSettings Advanced PPPoE Advanced PPPoEAction StatusSettings Advanced Pptp Advanced PptpAdvanced Setup Host IP SetupSettings Host IP Setup Host Network IdentityHost & Group Host NetworkBinding ListConnecting to the Virtual Servers Virtual ServersServer Type Settings Virtual ServerEnable AddressSelect Custom Server Server List Name Settings Custom Virtual ServersCustom Virtual Servers Custom ServerCustom Virtual Server Special Applications Settings Special ApplicationsSelect Special Application Name Select Name Item Using a Special Application on your PC To use the Dynamic DNS feature Dynamic DNSSettings Dynamic DNS Dynamic DNS ServiceStandard SettingsAdditional Client orMulti DMZ Multi DMZSettings Multi DMZ UPnP Settings UPnPUPnP Option NAT Setting NATSettings NAT NAT AliasAdvanced Features 10 Advanced FeatureSettings Advanced Features Interface Smtp Simple Mail Transport Protocol Binding Using Remote Web-based SetupProtocol Protocol and Port Binding Security Management Block URLSettings Block URL Block InternetAccess Filter Setup Access GroupPorts Filter SettingBlock Well-known Icmp FiltersSession Limit Protocol Setting System Filter Exception EnableSystem Filter Exception Foreign Port RangeVPN Configuration Planning the VPNIPSec Global Setting IPSec Global SettingIP Global Setting Log LevelPolicy Setup Policy SetupTraffic Selector VPN Policy SetupIPSec Traffic Binding Security LevelKey Management Dead Peer Detection Tunnel AttributeSet Options QoS Configuration QoS SetupService Policy ConfigurationData QoS Setup FeatureData Policy Configuration Network Admission PolicyManagement Assistant SnmpSystem Settings SnmpEmail Alert InformationSettings Email Alert Syslog Keep Sent Messages Syslog ConfigurationSyslog Global Syslog ServerAdmin Password Admin Password ScreenUpgrade Firmware Upgrade FirmwareExisting Dhcp Server Advanced LAN ConfigurationRouting Settings Routing Configuring Other Routers on your LANStatic Routing Example For the VPN 800/2 Firewall Router Gateways Routing Table For Router As Default RouteFor Router Bs Default Route Entry 1 SegmentOperation Operation and StatusSystem Status Data System Status DeviceRestore Factory Defaults Restore Factory DefaultsWAN Status WAN StatusNAT Status Data NAT StatusNAT Connections ErrorsNAT Traffic MiscFCC Statement SpecificationsCE Marking Warning Overview TCP/IP Settings Windows TCP/IP SetupChecking TCP/IP Settings Windows 9x/ME Using Dhcp Checking TCP/IP Settings Windows Select Control Panel Network and Dial-up ConnectionUsing a fixed IP Address Use the following IP Address Checking TCP/IP Settings Windows XP Figure B-7 Network Configuration Windows XPFigure B-8 TCP/IP Properties Windows XP Internet Access TroubleshootingGeneral Problems SolutionSolution