Dell 100-Mbps manual System Unit, Smart Support, System Power Supply

Page 16

SMART Support

The system has SMART-compliant hard-disk drives and SMART support in the system BIOS, which warns you at system start-up if a hard-disk drive has become unreliable.

System Unit

The following subsections provide service-related information about the system unit.

System Power Supply

The 230-W system power supply can operate from an AC power source of

115 VAC at 60 Hz or 230 VAC at 50 Hz. The system power supply provides the DC operating voltages and currents listed in Table 1-1.

NOTE: The power supply produces DC voltages only under its loaded condi- tion. Therefore, when you measure these voltages, the DC power connectors must be connected to their corresponding power input connectors on the system board or drives.

.

Table 1-1. DC Voltage Ranges

Voltage

Range

Maximum Output

Current1

+3.3 VDC

+3.15 to +3.45 VDC

14.0 A

+5 VDC

+4.75 to +5.25 VDC

29.0 A

+12 VDC

+11.40 to +12.60 VDC

6.0 A

–12 VDC

–10.80 to –13.20 VDC

0.3 A

–5 VDC

–4.50 to –5.50 VDC

0.3 A

+5 VFP 2

+4.75 to +5.25 VDC

10 mA

1Maximum continuous DC output power shall not exceed 230 W. Maximum combined load on +5 VDC and +3.3 VDC shall not exceed 170 W.

2VFP (volts flea power) — sometimes called “standby power.”

.

Pin Assignments for the DC Power Connectors

The power-supply output voltages can be measured at the back (wire side) of the connectors without disconnecting them. The following illustrations show the wire side of the connectors.

1-8 Dell OptiPlex GXpro Systems Service Manual

Image 16
Contents 659,&0$18$ Page Contents Chapter Beep Codes and Error Messages Chapter Basic TroubleshootingChapter Removing and Replacing Parts Index FiguresTables 16. Expansion-Card Cage RemovalPage Read This First System Overview System Features System Unit Orientation Front-Panel Features Dual-Processor Capability Advanced Expansion SubsystemHard-Disk Drive Options Enhanced Dual-Interface Eide SubsystemAudio Controller PCI Video CardDesktop Chassis Thermal MonitoringSystem Power Supply Pin Assignments for the DC Power ConnectorsSystem Unit Smart SupportDC Power Connector P1 DC Power Distribution DC Power Connector P7Power Distribution System Board Layout Video MemoryMain Memory System Board JumpersInterrupt Assignments Jumper DescriptionsDMA Channel Assignments IRQ14Technical Specifications Technical SpecificationsNIC CtrlAltEnter To 149 F Page Basic Troubleshooting Initial User ContactExternal Visual Inspection Observing the Boot Routine Internal Visual Inspection Running the Diskette-Based Diagnostics Eliminating Resource ConflictsGetting Help Beep Codes and Error Messages Post Beep CodesPost Beep Codes System Error Messages HaltedSystem Error Messages System could not suc System Setup program Incorrect configuration During memory test Faulty or improperly System does not recog Faulty diskette, diskette MS-DOS unable to Defective sectors on dis At system start-up One or both micro Removing and Replacing Parts Recommended ToolsPrecautionary Measures Protection of the EquipmentFloor Stand Pull the floor stand away from the system unitSystem Unit Cover System-Unit Cover RemovalEject, Power, and Reset Buttons Eject, Power, and Reset Button RemovalFront-Panel Inserts Front-Panel Insert RemovalIndicator Card Indicator Card RemovalSpeaker Speaker RemovalDrives Drive HardwareDrives in the Drive Cage 5-Inch Diskette Drive Removal10 .25-Inch Drive Removal Hard-Disk Drives Lift the hard-disk drive bracket out of the system unit12. Hard-Disk Drive Removal System Power Supply 13. Power Supply RemovalMicroprocessor Fan 14. Microprocessor Fan RemovalSystem Board Components 15. System Board ComponentsExpansion Cards Expansion-Card CageExpansion Card 17. Expansion-Card RemovalRiser Board 18. Riser Board RemovalDIMMs 19. Dimm RemovalMicroprocessor/Heat Sink Assembly 21. Microprocessor Securing Clip22. Microprocessor Removal Terminator or Add-In Card Terminator CardAdd-In Card 24. Add-In Card RemovalSystem Battery Remove the batterySystem Board Remove the system board as followsSystem Setup Program System Setup Screens USBTable A-1. System Setup Categories Be shadowed or cached. If video problems Check the monitor documentation to make Table A-1. System Setup Categories Index Dskt connector, 1-12,4-16dual-processing,1-5 ECC DIMMs LINE-IN connector, 1-12,4-16 USB description Location, 1-4,1-12