Dell 100-Mbps manual Check the monitor documentation to make

Page 75

Table A-1. System Setup Categories (continued)

Category

Function

Power Management

With the Power Management category

 

enabled, DPMS monitors and most EIDE

 

drives automatically switch into low-power

 

mode during periods of system inactivity.

 

CAUTION: Before enabling this feature,

 

check the monitor documentation to make

 

sure the system has a DPMS-compliant

 

monitor. Otherwise, there is a risk of dam-

 

aging the monitor.

 

NOTE: Not all EIDE hard-disk drives support

 

this feature. Enabling this feature for drives

 

that do not support it may cause the EIDE

 

drive to become inoperable until the system is

 

restarted and the Power Management category

 

is disabled.

 

 

Sound

Enables (On [default]) or disables (Off) the

 

audio controller.

 

 

NIC

Enables (On) or disables (Off) the network

 

interface controller.

 

 

Mouse

Enables or disables the built-in PS/2-

 

compatible mouse port.

 

 

Serial Port 1

Configures system’s built-in serial ports.

Serial Port 2

 

 

 

Parallel Port

Configures system’s built-in parallel port. The

 

port’s I/O address may be set to 278H, 3BCH,

 

or 378H. Otherwise, the port may be dis-

 

abled.

 

 

Parallel Modes

Controls whether system’s built-in parallel port

 

acts as an AT-compatible (unidirectional) or

 

PS/2-compatible (bidirectional) port.

 

 

IDE Hard Disk

Enables system’s built-in EIDE hard-disk drive

 

interface.

 

 

Diskette

Enables system’s built-in diskette controller.

 

 

USB

Enables (On) or disables (Off [default]) the

 

USB connectors.

 

NOTE: This category appears only on GXpro

 

systems containing the 10/100-Mbps Ethernet

 

NIC.

 

 

Speaker

Enables on-board speaker.

 

 

System Setup Program

A-5

Image 75
Contents 659,&0$18$ Page Contents Chapter Basic Troubleshooting Chapter Beep Codes and Error MessagesChapter Removing and Replacing Parts Figures Index16. Expansion-Card Cage Removal TablesPage Read This First System Overview System Features System Unit Orientation Front-Panel Features Advanced Expansion Subsystem Dual-Processor CapabilityPCI Video Card Hard-Disk Drive OptionsEnhanced Dual-Interface Eide Subsystem Audio ControllerThermal Monitoring Desktop ChassisSmart Support System Power SupplyPin Assignments for the DC Power Connectors System UnitDC Power Connector P1 DC Power Connector P7 DC Power DistributionPower Distribution Video Memory System Board LayoutSystem Board Jumpers Main MemoryJumper Descriptions Interrupt AssignmentsIRQ14 DMA Channel AssignmentsTechnical Specifications Technical SpecificationsNIC CtrlAltEnter To 149 F Page Initial User Contact Basic TroubleshootingExternal Visual Inspection Observing the Boot Routine Internal Visual Inspection Eliminating Resource Conflicts Running the Diskette-Based DiagnosticsGetting Help Post Beep Codes Beep Codes and Error MessagesPost Beep Codes Halted System Error MessagesSystem Error Messages System could not suc System Setup program Incorrect configuration During memory test Faulty or improperly System does not recog Faulty diskette, diskette MS-DOS unable to Defective sectors on dis At system start-up One or both micro Recommended Tools Removing and Replacing PartsProtection of the Equipment Precautionary MeasuresPull the floor stand away from the system unit Floor StandSystem-Unit Cover Removal System Unit CoverEject, Power, and Reset Button Removal Eject, Power, and Reset ButtonsFront-Panel Insert Removal Front-Panel InsertsIndicator Card Removal Indicator CardSpeaker Removal SpeakerDrive Hardware Drives5-Inch Diskette Drive Removal Drives in the Drive Cage10 .25-Inch Drive Removal Lift the hard-disk drive bracket out of the system unit Hard-Disk Drives12. Hard-Disk Drive Removal 13. Power Supply Removal System Power Supply14. Microprocessor Fan Removal Microprocessor Fan15. System Board Components System Board ComponentsExpansion-Card Cage Expansion Cards17. Expansion-Card Removal Expansion Card18. Riser Board Removal Riser Board19. Dimm Removal DIMMs21. Microprocessor Securing Clip Microprocessor/Heat Sink Assembly22. Microprocessor Removal Terminator Card Terminator or Add-In Card24. Add-In Card Removal Add-In CardRemove the battery System BatteryRemove the system board as follows System BoardSystem Setup Program USB System Setup ScreensTable A-1. System Setup Categories Be shadowed or cached. If video problems Check the monitor documentation to make Table A-1. System Setup Categories Index Dskt connector, 1-12,4-16dual-processing,1-5 ECC DIMMs LINE-IN connector, 1-12,4-16 USB description Location, 1-4,1-12