Dell 100-Mbps manual During memory test Faulty or improperly

Page 41

Table 3-2. System Error Messages (continued)

Message

Definition

Probable Causes

 

 

 

Memory

During memory test,

Faulty or improperly

address line

value read at address

seated DIMMs or defec-

failure at

was incorrect.

tive system board.

address, read

 

 

value expect-

 

 

ing value

 

 

Memory data

 

 

line failure

 

 

at address,

 

 

read value

 

 

expecting value

 

 

Memory double

 

 

word logic

 

 

failure at

 

 

address, read

 

 

value expect-

 

 

ing value

 

 

Memory odd/

 

 

even logic

 

 

failure at

 

 

address, read

 

 

value expect-

 

 

ing value

 

 

Memory write/

 

 

read failure

 

 

at address,

 

 

read value

 

 

expecting value

 

 

 

 

 

Memory alloca-

Software in use con-

Faulty application pro-

tion error

flicts with operating

gram or utility.

 

system, application pro-

 

 

gram, or utility.

 

 

 

 

Memory tests

Memory test did not

POST memory test termi-

terminated by

complete.

nated by pressing

keystroke

 

<Spacebar>.

 

 

 

"Network card

System does not detect

Incorrect NIC drivers

is not

NIC.

installed.

present in

 

 

the system"

 

 

 

 

 

Beep Codes and Error Messages

3-7

Image 41
Contents 659,&0$18$ Page Contents Chapter Removing and Replacing Parts Chapter Basic TroubleshootingChapter Beep Codes and Error Messages Figures Index16. Expansion-Card Cage Removal TablesPage Read This First System Overview System Features System Unit Orientation Front-Panel Features Advanced Expansion Subsystem Dual-Processor CapabilityEnhanced Dual-Interface Eide Subsystem Hard-Disk Drive OptionsAudio Controller PCI Video CardThermal Monitoring Desktop ChassisPin Assignments for the DC Power Connectors System Power SupplySystem Unit Smart SupportDC Power Connector P1 DC Power Connector P7 DC Power DistributionPower Distribution Video Memory System Board LayoutSystem Board Jumpers Main MemoryJumper Descriptions Interrupt AssignmentsIRQ14 DMA Channel AssignmentsTechnical Specifications Technical SpecificationsNIC CtrlAltEnter To 149 F Page Initial User Contact Basic TroubleshootingExternal Visual Inspection Observing the Boot Routine Internal Visual Inspection Eliminating Resource Conflicts Running the Diskette-Based DiagnosticsGetting Help Post Beep Codes Beep Codes and Error MessagesPost Beep Codes Halted System Error MessagesSystem Error Messages System could not suc System Setup program Incorrect configuration During memory test Faulty or improperly System does not recog Faulty diskette, diskette MS-DOS unable to Defective sectors on dis At system start-up One or both micro Recommended Tools Removing and Replacing PartsProtection of the Equipment Precautionary MeasuresPull the floor stand away from the system unit Floor StandSystem-Unit Cover Removal System Unit CoverEject, Power, and Reset Button Removal Eject, Power, and Reset ButtonsFront-Panel Insert Removal Front-Panel InsertsIndicator Card Removal Indicator CardSpeaker Removal SpeakerDrive Hardware Drives5-Inch Diskette Drive Removal Drives in the Drive Cage10 .25-Inch Drive Removal Lift the hard-disk drive bracket out of the system unit Hard-Disk Drives12. Hard-Disk Drive Removal 13. Power Supply Removal System Power Supply14. Microprocessor Fan Removal Microprocessor Fan15. System Board Components System Board ComponentsExpansion-Card Cage Expansion Cards17. Expansion-Card Removal Expansion Card18. Riser Board Removal Riser Board19. Dimm Removal DIMMs21. Microprocessor Securing Clip Microprocessor/Heat Sink Assembly22. Microprocessor Removal Terminator Card Terminator or Add-In Card24. Add-In Card Removal Add-In CardRemove the battery System BatteryRemove the system board as follows System BoardSystem Setup Program USB System Setup ScreensTable A-1. System Setup Categories Be shadowed or cached. If video problems Check the monitor documentation to make Table A-1. System Setup Categories Index Dskt connector, 1-12,4-16dual-processing,1-5 ECC DIMMs LINE-IN connector, 1-12,4-16 USB description Location, 1-4,1-12