Dell 180, 4100, 200 service manual External Visual Inspection

Page 32

External Visual Inspection

The external visual inspection consists of a quick inspection of the exterior of the computer, the monitor, the keyboard, any peripherals, and cables. While per- forming the visual inspection, make any necessary corrections. To perform the external visual inspection, follow these steps:

1.Turn off the computer, the monitor, and all peripherals.

2.Verify that all power cables are properly connected to the computer, the monitor and peripherals, and their power sources.

3.Verify that the keyboard and mouse interface cables are firmly attached to the proper connectors on the back of the computer.

For a PS/2-compatible mouse, the keyboard and mouse interface cable con- nectors are identical except for their labels (see Figure 1-5).

For a serial mouse, the mouse interface cable must be attached to one of the serial port connectors, and its captive screws must be secure enough to ensure a firm connection.

4.Verify that any devices attached to the serial and parallel port connec- tors are properly connected.

Each of the serial and parallel interface cables must be attached to an appro- priate connector on the back of the computer as well as to the interface connector on the device. The captive screws that secure these connectors at each end of the interface cable must be secure enough to ensure a firm connection.

5.Verify that the video interface cable is firmly attached to the connector on the I/O panel and to the connector on the back of the monitor.

For proper connection of the video interface cable, see the documentation for the monitor.

6.Inspect all external monitor controls for any obvious damage or improper settings.

For proper settings of the video monitor controls, see the documentation for the monitor.

7.Inspect the keyboard to ensure that no keys are sticking.

If one or more keys are sticking, it may be necessary to replace the keyboard.

8.Inspect the exterior of the computer, including all controls and indica- tors, and all user-accessible data storage devices for any signs of physical damage.

Does the inspection reveal any problems?

Yes. Proceed to the appropriate procedure in Chapter 4, “Removing and Replacing Parts.”

No. Proceed to the next section, “Observing the Boot Routine.”

2-2 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual

Image 32
Contents Dell PowerEdge 4100/180 and 4100/200 Systems Page System Features System OverviewPage Computer Orientation Front-Panel Features Front/Left Internal View Back/Right Internal View I/O Panel Integrated Server Management System MemoryAdvanced Expansion Subsystem Scsi Configuration Guidelines Video ControllerIntegrated Scsi Controllers Scsi Hard-Disk DrivesScsi ID Numbers DC Voltage Ranges System Power SupplySystem Unit Power Supply Connectors DC Power Connector J11 P1 DC Power Connectors J12 P2, J13 P3, and J14 P4 Ddbp 12. Power-Supply Paralleling Board Connectors 13. DC Power Connector PWR1 15. DC Power Connector Pwrscsi Ddbp DC Power Distribution Redundant System System Board Layout 18. System Board ComponentsMain Memory Interrupt Assignments Interrupt AssignmentsJumper Descriptions DMA Channel Assignments Dreq Line AssignmentsTechnical Specifications Technical SpecificationsSystem Clocks CD-ROM Power Technical Specifications Basic Troubleshooting Initial User ContactExternal Visual Inspection Observing the Boot Routine Internal Visual Inspection Running the System Diagnostics Eliminating Resource ConflictsGetting Help Post Beep Codes Beep CodesBeep Codes System Error Messages System Error MessagesReal-time clock on Defective micro Wrong microprocessor Replace microprocessor Page Removing and Replacing Parts Recommended ToolsPrecautionary Measures Computer CoversKeylocks on Computer’s Back Panel Front Bezel Front Bezel RemovalDrives Drive HardwareFront-Panel Inserts Front-Panel Insert RemovalExternally Accessible Drives Externally Accessible Drives RemovalDrive-Mounting Rails Removal Hard-Disk Drives Hard-Disk Drive Carrier RemovalHard-Disk Drive Removal Scsi Backplane Board 10. Scsi Backplane Board RemovalPower Supply 11. Power Supply RemovalPower-Supply Paralleling Board 12. Power-Supply Paralleling Board Removal Redundant SystemsPower Connector Panel 13. Power Connector Panel Removal Nonredundant SystemsControl Panel 14. Control Panel RemovalCooling Fans 15. Cooling Fan RemovalSystem Board Components 16. System Board ComponentsExpansion Cards 17. Expansion Card RemovalDIMMs 18. Dimm Removal20. Microprocessor Configuration Microprocessor and Heat Sink21. Microprocessor Securing Clip 23. Pin-1 Identification System Battery 24. System Battery RemovalSystem Board 25. System Board RemovalSystem Setup Screens Screen ConventionsKey Functions Table A-1. Key FunctionsScreen Color Combinations Main MenuTable A-2. Main Menu Categories Boot Options Submenu PostAdvanced Menu Figure A-3. Advanced MenuTable A-4. Advanced Menu Categories Security Menu Figure A-4. Security MenuTable A-5. Security Menu Categories User’s GuideExit Menu Figure A-5. Exit MenuTable A-6. Exit Menu Categories Page Index Dreq line assignments Scsi Key functions, A-2main menu, A-3menus, A-1
Related manuals
Manual 102 pages 48.06 Kb Manual 71 pages 2.41 Mb Manual 132 pages 53.29 Kb Manual 157 pages 30.57 Kb Manual 6 pages 26.32 Kb Manual 214 pages 18.44 Kb