Datamax Allegro 2 manual Invalid Font Type

Page 52

Creating Labels Using Internal Batch Software

∙Y is another special font choice that is not actually a font. The Y font selects a graphic image that has already been loaded into the memory module. If this font is selected, enter the name of the graphic image in the Data/Prompt position. This name must be uppercase characters when printing an image.

If any letter or number is entered in the FNT Position other than those specified above, the following error message will appear:

INVALID FONT TYPE

You will need to re-enter the data. After entering the desired font and pressing the return key, the cursor will move to the XW position.

6.The XW and XH positions are used to magnify widths and heights of fonts, and to change the wide/narrow ratio of barcodes.

∙If you wish to magnify the width of a font, valid responses are 1 through 9 and A through O. The default value is 1 for fonts.

∙If you wish to magnify the width of a barcode, valid responses are 1 through 9 and A through K. The default is 3 for ratio-based barcodes, 2 for fonts Q & R and 1 for all other barcode fields. If the pixel width is 1, the result will be a 5 mil (.0005") wide bar. If the pixel width is 2, the result will be a 10 mil (.010")wide bar. Pixel sizes by label format are specified in the Print Parameters screen.

∙Enter the desired XW dimension and press the return key. The cursor will move to the XH position.

44

Allegro2

Image 52

Contents Allegro2 Operator’s Manual Part Number Revision A3 Agency Compliance and Approvals Page Important Safety Instructions Page Contents Maintenance Introduction Getting StartedUnpacking and Inspection Location of Parts on Your Printer Mechanism DetailRear View Tear- off Assembly Installation Tear Bar Assembly InstallationUsing the Printer Control Panel Buttons, Lights and SwitchesGetting Started Switch Paper/RibbonLight RibbonInstallation Media InstallationLabels Label Loading Instructions Ribbon Loading Instructions Ribbon LoadingTo install a Memory Module Using the Printer OptionsAvailable Modules Options CutterFont ROM Modules 256K and 512K RAM ModulesPresent Sensor Peel and PresentMedia Rewinder Getting Started Allegro2 Power Up Self-Test Setting Up Your PrinterChecking Voltage Selection Test Label Part Number Description Interfacing to the PrinterInterface Cables Connecting to a CRT Sample InstallationsConnecting to a PC Connecting to Your Minicomputer Connecting to Your Non-ASCII DeviceSwitch Settings Switch SettingsSetting the Baud Rate Baud 9600 4800 2400 1200 300 TestBaud Rate Word LengthOther Switches Switch Settings and FunctionsProgramming Commands Immediate CommandsSystem-Level Commands Char Description FormatBatch, 1-Cutter Enable Label-Formatting Commands Description FormatSpecial Label-Formatting Commands 10 Font-Loading Commands Programming ExamplesExample line Setting Up Your Printer Allegro2 Creating Labels Using Internal Batch Software Printer Used With a Link CRT Check Link CRT SettingsConnect Cables Function Default Settings Batch System InitializationVerify Setup, Power Up, and Load Media Formatting and Printing Labels Available Fonts and BarcodesMenu Screens Function KeysLabel Name NEW Label Name ALT-P Screen Description Default Range Print ParametersOther Important Keys Create/Modify Label Screen Print Label Screen HeaderCreating Labels Using Internal Batch Software Sample Label Format Creating Labels Using Internal Batch Software Invalid Font Type Smooth Font Valid BH Ranges Smooth Font InformationNumber OUT of Range Creating Labels Using Internal Batch Software Not Enough Room for Field Data Lines Lhhhvvv Creating Labels Using Internal Batch Software Time and Date Information Format = Day number 1 = MondaySample PrintsPrint Label Screen Print Label ScreenCreating Labels Using Internal Batch Software System Maintenance Screen System Maintenance MenuReset Printer Copy ModuleMetric Print Test LabelCommand Valid Inputs Create/Modify Label CommandsQuick Reference Listing Special Keys Print Parameters ALT-PKey Function Troubleshooting Controlling Print Quality Mechanical Adjustments Aligning the PrintheadDirect-Thermal Stock Tag Stock or Stiff MediaPrinthead Alignment Label Stock Tracking Adjustment Printhead Alignment ProcedureRibbon Feed and Tracking Adjustments Fine Printhead Alignment Troubleshooting Allegro2 Adjusting Printhead Pressure and Support Printhead Mount AssemblyUnacceptable Print Quality TroubleshootingPrinter Does Not Print, or Prints Several Labels at once Erratic Printing Ribbon Does Not AdvanceSkips Every Other Label Unable to print in rotationPrints Light on the Right Side of the Label Printer fails to turn onInterior and Exterior MaintenanceDrive Roller Cleaning Schedule Area Method IntervalCleaning the Printhead Cleaning the PrintheadMaintenance Allegro2 Page Ascii Control Code Chart Appendix aMaintenance Allegro2 Char Hex Dec Page Appendix B Switch Settings and Cable Interfacing Table B-1 Baud RateTable B-2 Word Length Table B-3 OptionsSignal Pin Table B-1 I/O Port WiringParamete Default Value Table B-2 Printer Default Communication ParametersAppendix C Available Fonts and BarcodesFonts Table C-1 Valid Human-Readable Font Ascii CharactersTable C-2 Font Sizes Font 6 62-character alphanumeric, uppercase Available Fonts and Barcodes Table C-3 Barcode Characteristics BarcodesHbic Barcode I Codabar Kmart NON EDI Error Codes LowercaseUppercase R Uppercase TAllegro2 Appendix E Table E-1 Printer Interface CablesPin Description Table E-2 Printer Pin ConnectionsStraight Cable MXM PC DB25P to Printer ∙ Parallel to Serial Adapter Part Number Figure E-5 Centronics Parallel Interface ConverterAppendix F PrintingFonts BarcodesMedia Label MaterialLabel/Tag Media Specifications Table F-1 Media DimensionsLights, Buttons, Switch and POT Lists of Approved MediaCommunications Interfacing ElectricalPhysical EnvironmentalOptions 256K Flash Eeprom Specifications Allegro2 Appendix G PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability