Citizen PPU-231 manual Citizen

Page 23

PPU-231 User’s Manual

(1)POWER switch

Turns on/off the power for the printer/presenter unit

(The POWER switch can be mounted either side of the unit.).

(2)FEED switch

Feeds the paper to exit the paper.

(3)Power connector

Connects to the optional AC adapter (31AD).

(The power connector can be mounted at any one of the 6 locations on the unit. See 4.1.1 ”Connecting the AC Adapter”.)

(4)Presenter

Feeds the paper roll.

(5)Auto Cutter

Automatically cuts the printed paper by a command. Either partial cut or full cut is selectable.

(6)DIP switches

Initially set the printer/presenter unit at power-on and set the functions.

(7)Interface connector

Connects to a communication interface cable. There are two types, for serial and parallel interfaces.

(8)Head-up lever

Used when inserting the paper or exiting the paper.

(9)Knob

Use this to manually feed the paper.

(10)Front door

Open this door to remove remaining paper inside the presenter.

10

CITIZEN

Image 23

Contents Line Thermal Printer Declaration of Conformity Important Safety Instructions Lärmemission kleiner 70dBA Wichtige SicherheitsanweisungenCitizen Be Sure to Observe Safety PrecautionsCitizen Precautions for Installation Precautions for Handling Daily Maintenance Contents DIP Switch Setting Appendix Unpacking FeaturesOutline PPU series Printer/Presenter unit Basic SpecificationsModel Classifications Options PHU series Paper holding unit 31AD series Power supply unitPMU series Printer mechanism unit MiscellaneousPRU series Presenter unit BD2 series Control PCB with accessories ESC/POS Basic Specifications Printing Position Paper Specifications Recommended Paper Printing Head and Paper Cutter Layout PPU Printer/Presenter Unit Outer Appearance and Component PartsCitizen Optional PHU Paper Holding Unit Operation Connecting the AC AdapterUsing the Power Connector GND Connecting a Power Cable to the Control PCBCN1 Connecting the Interface Cable ACK STBBusy DSR DTRTXD RXDInserting the Paper How to Remove Remaining Paper Roll Eliminating a Jam in the Printer Mechanism Eliminating the Paper JamEliminating a Jam in the Presenter Paper End Function Feed Switch FunctionReleasing a Locked Cutter PNE Connecting the PHU Paper Holding UnitPaper Near End Function When Using the PHU CN5Presenter Control Auto-Loading FunctionSelf-Print Function Location of DIP Switch DIP Switch SettingBaud rate and parity setting DIP Switch FunctionDIP switch 1 DS1 DIP switch 2 DS2Print density Strobe Twisted Pair GND Data ACK Busy Reset Fault Frame GND SpecificationsConnectors Pin Configuration ACK, BUSY, STROBE, FAULT, PE, ResetStrobe Input and Output SignalsInput and Output Signals Electrical Characteristics Buffering Timing ChartData Receiving Control Serial Interface Input and Output Signals Error Detection Data ConfigurationOutput TXD, DTR Printer Side Electrical Characteristics RS-232C CircuitPower Connector Maintenance and Service Print Control Functions Commands List1DH 3AH Description of Items Command DetailsESC D DetailsESC SP ESC Lprint CHR$ &HA ESC ESC %ESC & s n P s × a m n +1 Citizen ESC ∗ m n1 N2 d k Example Sample Program ESC − n ESC 3 n ESC = 52CITIZEN ESC D n NUL ESC E ESC E ESC GESC R Condition Canceling 90-right- turned Characters Position ESC c Parallel Interface Only ESC d ESC cESC When Using Auto Cutter ESC m When Using Auto Cutter ESC t XON/XOFF ESC Serial Interface OnlyInverted printing means printing the line at 180turned ESC ¥ ESC $ n1ESC $ Type OnlyUPC-A GS k nUPC-A UPC-E JAN13 EAN JAN 8 EAN Code Codabar NW-7ITF JAN-13EANJAN-8EAN CODE39Code Btestcode A123 TestUPC-A GS w GS h n Specify before the GS k command GS H GS f nGS ∗ n1 N2 d n1 × n2 × Sample Program Print Results 203 DPI Double wide mode Lprint CHR$ GS n1 n2 n3 International Character Codes TableJapanese International Character Code Table Appendix 1. Block Diagram Unit mm Appendix 2. Outline Drawing for PPUAppendix 3. Outline Drawing for PHU