Citizen PPU-231 manual Auto-Loading Function, Self-Print Function, Presenter Control

Page 36

PPU-231 User’s Manual

4.11Auto-Loading Function

This printer has a function to automatically set the paper. When the paper is set and the paper end sensor and paper near end sensor are not detected, and the head-up lever is lowered, the paper will be automatically fed by a constant amount in about 1 second.

If the paper is not automatically fed, remove the paper from the paper insertion slot and try again.

You can use the DIP switch to enable/disable the function. If disabled, auto-loading will not be performed.

CAUTION:

1)When auto-loading is being activated, do not touch the paper roll, because it could result in a paper feed failure or cause the paper to be one-sided.

2)Be sure to set the paper until it comes into contact with the platen roller; otherwise, the paper cannot be fed and the printing head could be damaged.

4.12Self-Print Function

This unit has a function to perform preset printing. Turn on the power with the FEED switch held down. It will print the ROM version, DIP switch state, characters used, etc.

CAUTION:

Do not use this function when the paper roll is running out.

4.13Presenter Control

This unit feeds in paper while printing or transporting paper.

After having operated the auto cutter, the unit delivers out the paper.

The next printing operation does not start until the paper ejected is removed. (Printing is holted.)

CAUTION:

Do not approach your face or hand toward the Presenter’s paper output slot while the paper is being output.

23

CITIZEN

Image 36
Contents Line Thermal Printer Declaration of Conformity Important Safety Instructions Wichtige Sicherheitsanweisungen Lärmemission kleiner 70dBACitizen Safety Precautions Be Sure to ObserveCitizen Precautions for Installation Precautions for Handling Daily Maintenance Contents DIP Switch Setting Appendix Features OutlineUnpacking Basic Specifications Model ClassificationsPPU series Printer/Presenter unit 31AD series Power supply unit Options PHU series Paper holding unitMiscellaneous PRU series Presenter unitPMU series Printer mechanism unit BD2 series Control PCB with accessories Basic Specifications ESC/POSPaper Specifications Recommended PaperPrinting Position Printing Head and Paper Cutter Layout Outer Appearance and Component Parts PPU Printer/Presenter UnitCitizen Optional PHU Paper Holding Unit Connecting the AC Adapter Using the Power ConnectorOperation Connecting a Power Cable to the Control PCB CN1GND Connecting the Interface Cable STB BusyACK DTR TXDRXD DSRInserting the Paper How to Remove Remaining Paper Roll Eliminating the Paper Jam Eliminating a Jam in the Printer MechanismEliminating a Jam in the Presenter Feed Switch Function Releasing a Locked CutterPaper End Function Connecting the PHU Paper Holding Unit Paper Near End Function When Using the PHUCN5 PNEAuto-Loading Function Self-Print FunctionPresenter Control DIP Switch Setting Location of DIP SwitchDIP Switch Function DIP switch 1 DS1DIP switch 2 DS2 Baud rate and parity settingPrint density Specifications Connectors Pin ConfigurationACK, BUSY, STROBE, FAULT, PE, Reset Strobe Twisted Pair GND Data ACK Busy Reset Fault Frame GNDInput and Output Signals Input and Output SignalsStrobe Electrical Characteristics Timing Chart Data Receiving ControlBuffering Serial Interface Input and Output Signals Data Configuration Error DetectionElectrical Characteristics RS-232C Circuit Output TXD, DTR Printer SidePower Connector Maintenance and Service Commands List Print Control Functions1DH 3AH Command Details Description of ItemsDetails ESC DESC SP ESC Lprint CHR$ &HA ESC % ESCESC & s n P s × a m n +1 Citizen ESC ∗ m n1 N2 d k Example Sample Program ESC − n ESC 3 n ESC = 52CITIZEN ESC D n NUL ESC E ESC G ESC EESC R Condition Canceling 90-right- turned Characters Position ESC c Parallel Interface Only ESC c ESC dESC When Using Auto Cutter ESC m When Using Auto Cutter ESC t ESC Serial Interface Only XON/XOFFInverted printing means printing the line at 180turned ESC $ n1 ESC ¥Type Only ESC $GS k n UPC-A UPC-E JAN13 EAN JAN 8 EAN CodeCodabar NW-7 UPC-AJAN-13EAN JAN-8EANCODE39 ITFTest Code Btestcode A123UPC-A GS w GS h n Specify before the GS k command GS f n GS HGS ∗ n1 N2 d n1 × n2 × Sample Program Print Results 203 DPI Double wide mode Lprint CHR$ GS n1 n2 n3 Character Codes Table InternationalJapanese International Character Code Table Appendix 1. Block Diagram Appendix 2. Outline Drawing for PPU Unit mmAppendix 3. Outline Drawing for PHU