Citizen PPU-231 manual Citizen

Page 7

PPU-231 User’s Manual

WARNING

zNever handle the equipment in the following manners, as it may break, become out of order, or overheat causing smoke and resulting in fire or electric shock.

If the equipment is used in an abnormal condition, such as when broken, then problems, smoke emission, abnormal odor/noise, and fire can result. If an abnormal condition exists, be sure to

disconnect the power plug from a plug socket, and contact our dealer. Never repair the equipment on your own - it is very dangerous.

Do not allow the equipment to receive a strong impact or shock, such as kicking, stomping, hitting, dropping, and the like.

Install the equipment in a well-ventilated place. Do not use it in such a manner that its ventilation port will be blocked.

Do not install the equipment in a place like a laboratory where chemical reactions are expected, or in a place where salt or gases are contained in the air.

Do not connect/disconnect a power cord or a data cable, while holding the cable. Do not pull, install, use, or carry the equipment in such a manner that force will be applied to the cables.

Do not drop or insert any foreign substances, such as clips or pins, into the equipment.

Do not spill any liquid or spray any chemical-containing liquid over the equipment. If any liquid is spilled on it, turn off the power, disconnect the power cable and power cord from the plug socket, and so on, and contact our dealer.

Never disassemble or remodel the equipment. Negligence of this may cause fire or electric shock.

Use the equipment only with the specified commercial power supply and AC adapter. Negligence of this may result in fire, electric shock, or problems.

If you drop or break the AC adapter, or if water or the like gets inside it, unplug it immediately from the socket and contact your dealer.

Do not damage, break, process, bend/pull by force, twist, or head an AC adapter cord. Also, do not put a heavy substance on it or heat it. The AC adapter cord could be broken, resulting in fire, electric shock, or trouble. If the AC adapter cord is damaged, contact our dealer.

Do not connect/disconnect the AC adapter with wet hands.

Do not overload a single electrical outlet, using a table tap or a current tap socket.

zAn equipment packing bag must be discarded or kept away from children. A child can suffocate if the bag is placed over the head.

CITIZEN

Image 7
Contents Line Thermal Printer Declaration of Conformity Important Safety Instructions Lärmemission kleiner 70dBA Wichtige SicherheitsanweisungenCitizen Be Sure to Observe Safety PrecautionsCitizen Precautions for Installation Precautions for Handling Daily Maintenance Contents DIP Switch Setting Appendix Outline FeaturesUnpacking Model Classifications Basic SpecificationsPPU series Printer/Presenter unit Options PHU series Paper holding unit 31AD series Power supply unitPRU series Presenter unit MiscellaneousPMU series Printer mechanism unit BD2 series Control PCB with accessories ESC/POS Basic SpecificationsRecommended Paper Paper SpecificationsPrinting Position Printing Head and Paper Cutter Layout PPU Printer/Presenter Unit Outer Appearance and Component PartsCitizen Optional PHU Paper Holding Unit Using the Power Connector Connecting the AC AdapterOperation CN1 Connecting a Power Cable to the Control PCBGND Connecting the Interface Cable Busy STBACK DSR DTRTXD RXDInserting the Paper How to Remove Remaining Paper Roll Eliminating a Jam in the Printer Mechanism Eliminating the Paper JamEliminating a Jam in the Presenter Releasing a Locked Cutter Feed Switch FunctionPaper End Function PNE Connecting the PHU Paper Holding UnitPaper Near End Function When Using the PHU CN5Self-Print Function Auto-Loading FunctionPresenter Control Location of DIP Switch DIP Switch SettingBaud rate and parity setting DIP Switch FunctionDIP switch 1 DS1 DIP switch 2 DS2Print density Strobe Twisted Pair GND Data ACK Busy Reset Fault Frame GND SpecificationsConnectors Pin Configuration ACK, BUSY, STROBE, FAULT, PE, ResetInput and Output Signals Input and Output SignalsStrobe Electrical Characteristics Data Receiving Control Timing ChartBuffering Serial Interface Input and Output Signals Error Detection Data ConfigurationOutput TXD, DTR Printer Side Electrical Characteristics RS-232C CircuitPower Connector Maintenance and Service Print Control Functions Commands List1DH 3AH Description of Items Command DetailsESC D DetailsESC SP ESC Lprint CHR$ &HA ESC ESC %ESC & s n P s × a m n +1 Citizen ESC ∗ m n1 N2 d k Example Sample Program ESC − n ESC 3 n ESC = 52CITIZEN ESC D n NUL ESC E ESC E ESC GESC R Condition Canceling 90-right- turned Characters Position ESC c Parallel Interface Only ESC d ESC cESC When Using Auto Cutter ESC m When Using Auto Cutter ESC t XON/XOFF ESC Serial Interface OnlyInverted printing means printing the line at 180turned ESC ¥ ESC $ n1ESC $ Type OnlyUPC-A GS k nUPC-A UPC-E JAN13 EAN JAN 8 EAN Code Codabar NW-7ITF JAN-13EANJAN-8EAN CODE39Code Btestcode A123 TestUPC-A GS w GS h n Specify before the GS k command GS H GS f nGS ∗ n1 N2 d n1 × n2 × Sample Program Print Results 203 DPI Double wide mode Lprint CHR$ GS n1 n2 n3 International Character Codes TableJapanese International Character Code Table Appendix 1. Block Diagram Unit mm Appendix 2. Outline Drawing for PPUAppendix 3. Outline Drawing for PHU