Citizen PPU-231 manual Precautions for Handling

Page 9

PPU-231 User’s Manual

PRECAUTIONS FOR HANDLING

Do not handle the equipment in the following manners, because problems may result.

Do not use any other power source besides the accessory AC adapter. Also, do not use the AC adapter for other purposes.

Do not print without paper.

Do not drop or put any foreign object, such as a clip, pin, or the like, inside the unit.

Do not spill any liquid or spray any chemical-containing liquid over the equipment.

Never use a pointed object, such as a pen, to operate the operation panel.

Do not use Scotch tape to fasten paper together for continuous use. It could damage the printing head.

Never pull the set paper forcibly. When opening/closing the unit cover, take care that the paper will not be caught. It could cause the paper to jam.

Be sure to use the specified paper. Use of other paper could deteriorate the print quality or cause a problem with the printing head.

To Prevent Injury and Spreading of Damage

Never touch the printing head, motor, or paper cutting blade. Your finger may be cut.

During power-on or immediately after printing, do not touch electrical parts or moving parts, such as the mechanism, motor, internal gear, etc. They may be very hot and can burn your hand/finger.

Be careful to avoid bodily injure or damaging other objects with an edge of sheet metal.

Should any error occur while operating the equipment, stop it immediately and disconnect the power plug from the plug socket.

Only a qualified serviceman is allowed to disassemble or repair the unit.

Should a problem occur, leave solving it to our serviceman. Do not disassemble the equipment on your own.

When opening/closing the unit cover, and so on, be careful not to catch your hand or finger on the equipment.

After using the equipment, turn off the power switch and unplug the AC adapter from a plug socket.

CITIZEN

Image 9
Contents Line Thermal Printer Declaration of Conformity Important Safety Instructions Lärmemission kleiner 70dBA Wichtige SicherheitsanweisungenCitizen Be Sure to Observe Safety PrecautionsCitizen Precautions for Installation Precautions for Handling Daily Maintenance Contents DIP Switch Setting Appendix Features OutlineUnpacking Basic Specifications Model ClassificationsPPU series Printer/Presenter unit Options PHU series Paper holding unit 31AD series Power supply unitMiscellaneous PRU series Presenter unitPMU series Printer mechanism unit BD2 series Control PCB with accessories ESC/POS Basic SpecificationsPaper Specifications Recommended PaperPrinting Position Printing Head and Paper Cutter Layout PPU Printer/Presenter Unit Outer Appearance and Component PartsCitizen Optional PHU Paper Holding Unit Connecting the AC Adapter Using the Power ConnectorOperation Connecting a Power Cable to the Control PCB CN1GND Connecting the Interface Cable STB BusyACK TXD DTRRXD DSRInserting the Paper How to Remove Remaining Paper Roll Eliminating a Jam in the Printer Mechanism Eliminating the Paper JamEliminating a Jam in the Presenter Feed Switch Function Releasing a Locked CutterPaper End Function Paper Near End Function When Using the PHU Connecting the PHU Paper Holding UnitCN5 PNEAuto-Loading Function Self-Print FunctionPresenter Control Location of DIP Switch DIP Switch SettingDIP switch 1 DS1 DIP Switch FunctionDIP switch 2 DS2 Baud rate and parity settingPrint density Connectors Pin Configuration SpecificationsACK, BUSY, STROBE, FAULT, PE, Reset Strobe Twisted Pair GND Data ACK Busy Reset Fault Frame GNDInput and Output Signals Input and Output SignalsStrobe Electrical Characteristics Timing Chart Data Receiving ControlBuffering Serial Interface Input and Output Signals Error Detection Data ConfigurationOutput TXD, DTR Printer Side Electrical Characteristics RS-232C CircuitPower Connector Maintenance and Service Print Control Functions Commands List1DH 3AH Description of Items Command DetailsESC D DetailsESC SP ESC Lprint CHR$ &HA ESC ESC %ESC & s n P s × a m n +1 Citizen ESC ∗ m n1 N2 d k Example Sample Program ESC − n ESC 3 n ESC = 52CITIZEN ESC D n NUL ESC E ESC E ESC GESC R Condition Canceling 90-right- turned Characters Position ESC c Parallel Interface Only ESC d ESC cESC When Using Auto Cutter ESC m When Using Auto Cutter ESC t XON/XOFF ESC Serial Interface OnlyInverted printing means printing the line at 180turned ESC ¥ ESC $ n1ESC $ Type OnlyUPC-A UPC-E JAN13 EAN JAN 8 EAN Code GS k nCodabar NW-7 UPC-AJAN-8EAN JAN-13EANCODE39 ITFCode Btestcode A123 TestUPC-A GS w GS h n Specify before the GS k command GS H GS f nGS ∗ n1 N2 d n1 × n2 × Sample Program Print Results 203 DPI Double wide mode Lprint CHR$ GS n1 n2 n3 International Character Codes TableJapanese International Character Code Table Appendix 1. Block Diagram Unit mm Appendix 2. Outline Drawing for PPUAppendix 3. Outline Drawing for PHU