AOC i2353 manual Wall Mounting

Page 13

Wall Mounting

Wall Mounting

Preparing to Install An Optional Wall Mounting Arm.





This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps:

1Place monitor on the firm surface (such as, table)

2Use your hands to hold the monitor base

3Use your hands to fold the monitor base as figure instructed above by switch safety lock to the right side

4Once the monitor base begin to fold you can release the safety lock (caution: you must hear “click” after you fold the monitor base to wall mount position to ensure safety lock is lock properly.)

5Follow the manufacturer's instructions to assemble the wall mounting arm.

6Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.

7Insert the 4 screws into the holes and tighten.

8Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall.

Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official department of AOC.

Screw mode: M4x8mm

13

Image 13

Contents Page Power SafetyInstallation CleaningWarranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil National Conventions SafetyPower Installation Cleaning Other Contents in Box SetupPower Cable Analog Cable HDMI Cable AdaptorSetup Stand & Base Adjusting Viewing Angle 1 2 3 4 Connecting the MonitorWall Mounting Setting Optimal Resolution AdjustingWindows Vista 1 Click START6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings2 Click SETTINGS 3 Click CONTROL PANEL 4 Click Appearance and Themes Windows XPFor Windows XP 5 Double click DISPLAY7 Set the resolution SLIDE-BAR to 1920 by Windows ME/20004 Double click DISPLAY Power HotkeysVolume Auto/Source/ExitClear Vision Basic and simple instruction on the control keys OSD SettingPress Menu to display menu LuminancePress or to select Luminance, and press to enter Press or to select submenu, and press to enterBacklight Adjustment Press or to adjustAdjust to Gamma1 Adjust to GammaPress or to select Image Setup, and press to enter Image SetupPhase Adjust picture Clock to reduce Vertical-Line noiseAdjust Picture Phase to reduce Horizontal-Line noise Adjust picture sharpnessPress or to select Color Setup, and press to enter Color SetupDisable or Enable Full Enhance Mode Color setupDisable or Enable Nature Skin Mode Disable or Enable Green Field ModePress or to select Picture Boost, and press to enter Picture BoostAdjust Frame Brightness Adjust Frame SizeAdjust Frame Contrast Adjust Frame horizontal PositionPress or to select OSD Setup, and press to enter OSD SetupAdjust the vertical position of OSD Adjust the horizontal position ofTimeout Adjust the OSD TimeoutPress or to select Extra, and press to enter ExtraHDMI 1/HDMI Exit LED IndicatorMonitor Driver DriverWindows 1.Start Windows5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 9. Select Let me pick from a list of device drivers on my computer 7.Click the “Driver” tab13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab2. Click on the Start button and then click on Control Panel 1. Start Windows XP3. Select and click on the category ‘Appearance and Themes’ 4. Click on the Display Item7. Click on the Driver tab and then click on Update Driver... button 5. Select the Settings tab then click on the Advanced button6. Select Monitor tab If the Properties button is active, click on Properties button12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Saver Screen+ Problem & Question TroubleshootPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active General Specification SpecificationRESOLUTION Preset Display ModesSTAND HORIZONTALSignal Name Pin AssignmentsPin No Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Warranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil ARGENTINA http//ar.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterCHILE http//cl.aoc.com/support/findservicecenter COLOMBIA http//co.aoc.com/support/findservicecenter