AOC i2353 Troubleshoot, Problem & Question, Power LED Is Not ON, No images on the screen, Picture

Page 47

Troubleshoot

	Problem & Question	Possible Solutions

		Make sure the power button is ON and the Power Cord is properly connected
	Power LED Is Not ON	to a grounded power outlet and to the monitor.

		Is the power cord connected properly?
		Check the power cord connection and power supply.
		Is the cable connected correctly?
		(Connected using the D-sub cable)
		Check the DB-15 cable connection.
		(Connected using the DVI cable)
		Check the DVI cable connection.
		* DVI input is not available on every model.
	No images on the screen	If the power is on, reboot the computer to see the initial screen (the login
	No images on the screen	screen), which can be seen.
		screen), which can be seen.
		If the initial screen (the login screen) appears, boot the computer in the
		applicable mode (the safe mode for Windows ME/XP/2000) and then change
		the frequency of the video card.
		(Refer to the Setting the Optimal Resolution)
		If the initial screen (the login screen) does not appear, contact the Service
		Center or your dealer.
		Can you see "Input Not Supported" on the screen?
		You can see this message when the signal from the video card exceeds the
		maximum resolution and frequency that the monitor can handle properly.
		Adjust the maximum resolution and frequency that the monitor can handle
		properly.
		Make sure the AOC Monitor Drivers are installed.

	Picture Is Fuzzy & Has	Adjust the Contrast and Brightness Controls.
	Ghosting Shadowing Problem	Press to auto adjust.
		Make sure you are not using an extension cable or switch box. We
		recommend plugging the monitor directly to the video card output connector
		on the back .

		Move electrical devices that may cause electrical interference as far away
	Picture Bounces, Flickers Or	from the monitor as possible.
	Wave Pattern Appears In The	Use the maximum refresh rate your monitor is capable of at the resolution
	Picture	your are using.

47

Image 47

Contents Page Cleaning SafetyPower InstallationWarranty Statement for North & South America excluding Brazil ServiceWarranty Statement for Europe National Conventions SafetyPower Installation Cleaning Other Adaptor SetupContents in Box Power Cable Analog Cable HDMI CableSetup Stand & Base Adjusting Viewing Angle 1 2 3 4 Connecting the MonitorWall Mounting 1 Click START AdjustingSetting Optimal Resolution Windows Vista6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings5 Double click DISPLAY Windows XP2 Click SETTINGS 3 Click CONTROL PANEL 4 Click Appearance and Themes For Windows XP4 Double click DISPLAY Windows ME/20007 Set the resolution SLIDE-BAR to 1920 by Auto/Source/Exit HotkeysPower VolumeClear Vision Basic and simple instruction on the control keys OSD SettingPress or to select submenu, and press to enter LuminancePress Menu to display menu Press or to select Luminance, and press to enterAdjust to Gamma Press or to adjustBacklight Adjustment Adjust to Gamma1Press or to select Image Setup, and press to enter Image SetupAdjust picture sharpness Adjust picture Clock to reduce Vertical-Line noisePhase Adjust Picture Phase to reduce Horizontal-Line noisePress or to select Color Setup, and press to enter Color SetupDisable or Enable Green Field Mode Color setupDisable or Enable Full Enhance Mode Disable or Enable Nature Skin ModePress or to select Picture Boost, and press to enter Picture BoostAdjust Frame horizontal Position Adjust Frame SizeAdjust Frame Brightness Adjust Frame ContrastPress or to select OSD Setup, and press to enter OSD SetupAdjust the OSD Timeout Adjust the horizontal position ofAdjust the vertical position of OSD TimeoutPress or to select Extra, and press to enter ExtraHDMI 1/HDMI Exit LED Indicator1.Start Windows DriverMonitor Driver Windows6.Click the “Monitor” tab and then click the “Properties” button 4.Ckick on the “Change display settings” button5.Click the “Advanced Settings” button 9. Select Let me pick from a list of device drivers on my computer 7.Click the “Driver” tab13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab4. Click on the Display Item 1. Start Windows XP2. Click on the Start button and then click on Control Panel 3. Select and click on the category ‘Appearance and Themes’If the Properties button is active, click on Properties button 5. Select the Settings tab then click on the Advanced button7. Click on the Driver tab and then click on Update Driver... button 6. Select Monitor tab13. Click on the Finish button then the Close button 11. Click on the Open button, then click the OK button12. Select your monitor model and click on the Next button Windows ME i-Menu e-Saver Screen+ Ghosting Shadowing Problem TroubleshootProblem & Question Power LED Is Not ONMonitor Is Stuck In Active General Specification SpecificationHORIZONTAL Preset Display ModesRESOLUTION STANDPin No Pin AssignmentsSignal Name Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Warranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil COLOMBIA http//co.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterARGENTINA http//ar.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter