AOC i2353 manual General Specification

Page 49

Specification

General Specification

		Model number	i2353

		Driving system	TFT Color LED IPS

		Viewable Image Size	58.42cm diagoanl

	Panel	Pixel pitch	0.265mm(H) x 0.265mm(V)

		Video	R, G, B Analog lnterface & Digital Interface
		Video	R, G, B Analog lnterface & Digital Interface

		Separate Sync.	H/V TTL

		Display Color	16.7M Colors

		Dot Clock	170 MHz

		Horizontal scan range	30 kHz - 83 kHz

		Horizontal scan Size(Maximum)	533.2mm

		Vertical scan range	50 Hz - 76 Hz

		Vertical scan Size(Maximum)	312.0mm

		Optimal preset resolution	1920 x 1080 (60 Hz)

	Resolution	Highest preset resolution	1920 x 1080 (60 Hz)
	Resolution
		Plug & Play	VESA DDC2B/CI

		Input Connector	D-Sub 15pin/ HDMI
		Input Video Signal	Analog: 0.7Vp-p(standard), 75 OHM, Positive; HDMI ; TMDS
		Power Source	100~240VAC, 50/60Hz

		Power Consumption	Active < 35 W (Typical)
		Power Consumption
			Standby < 0.5 W

		Connector Type	15-pin Mini D-Sub, HDMI

		Signal Cable Type	Detachable

	Physical	Dimensions & Weight:

		Height (with base)	388.3 mm
	Characteristics		388.3 mm

		Width	549.5 mm
		Width	549.5 mm

		Depth	185.7 mm

		Weight (monitor only)	2.85 kg

	Environmental	Temperature:

		Operating	0°C to 40° C

		Non-Operating	-25°Cto 55°C

		Humidity:

		Operating	10% to 85% (non-condensing)

		Non-Operating	5% to 93% (non-condensing)

49

Image 49

Contents Page Power SafetyInstallation CleaningWarranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil National Conventions SafetyPower Installation Cleaning Other Contents in Box SetupPower Cable Analog Cable HDMI Cable AdaptorSetup Stand & Base Adjusting Viewing Angle 1 2 3 4 Connecting the MonitorWall Mounting Setting Optimal Resolution AdjustingWindows Vista 1 Click START6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings2 Click SETTINGS 3 Click CONTROL PANEL 4 Click Appearance and Themes Windows XPFor Windows XP 5 Double click DISPLAY7 Set the resolution SLIDE-BAR to 1920 by Windows ME/20004 Double click DISPLAY Power HotkeysVolume Auto/Source/ExitClear Vision Basic and simple instruction on the control keys OSD SettingPress Menu to display menu LuminancePress or to select Luminance, and press to enter Press or to select submenu, and press to enterBacklight Adjustment Press or to adjustAdjust to Gamma1 Adjust to GammaPress or to select Image Setup, and press to enter Image SetupPhase Adjust picture Clock to reduce Vertical-Line noiseAdjust Picture Phase to reduce Horizontal-Line noise Adjust picture sharpnessPress or to select Color Setup, and press to enter Color SetupDisable or Enable Full Enhance Mode Color setupDisable or Enable Nature Skin Mode Disable or Enable Green Field ModePress or to select Picture Boost, and press to enter Picture BoostAdjust Frame Brightness Adjust Frame SizeAdjust Frame Contrast Adjust Frame horizontal PositionPress or to select OSD Setup, and press to enter OSD SetupAdjust the vertical position of OSD Adjust the horizontal position ofTimeout Adjust the OSD TimeoutPress or to select Extra, and press to enter ExtraHDMI 1/HDMI Exit LED IndicatorMonitor Driver DriverWindows 1.Start Windows5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 9. Select Let me pick from a list of device drivers on my computer 7.Click the “Driver” tab13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab2. Click on the Start button and then click on Control Panel 1. Start Windows XP3. Select and click on the category ‘Appearance and Themes’ 4. Click on the Display Item7. Click on the Driver tab and then click on Update Driver... button 5. Select the Settings tab then click on the Advanced button6. Select Monitor tab If the Properties button is active, click on Properties button12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Saver Screen+ Problem & Question TroubleshootPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active General Specification SpecificationRESOLUTION Preset Display ModesSTAND HORIZONTALSignal Name Pin AssignmentsPin No Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Warranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil ARGENTINA http//ar.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterCHILE http//cl.aoc.com/support/findservicecenter COLOMBIA http//co.aoc.com/support/findservicecenter