AOC i2353 manual Plug and Play, Plug & Play DDC2B Feature

Page 52

Plug and Play

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.

Image 52

Contents Page Safety PowerInstallation CleaningWarranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil Safety National ConventionsPower Installation Cleaning Other Setup Contents in BoxPower Cable Analog Cable HDMI Cable AdaptorSetup Stand & Base Adjusting Viewing Angle Connecting the Monitor 1 2 3 4Wall Mounting Adjusting Setting Optimal ResolutionWindows Vista 1 Click START5 Click Display Settings 6 Set the resolution SLIDE-BAR to 1920 byWindows XP 2 Click SETTINGS 3 Click CONTROL PANEL 4 Click Appearance and ThemesFor Windows XP 5 Double click DISPLAY7 Set the resolution SLIDE-BAR to 1920 by Windows ME/20004 Double click DISPLAY Hotkeys PowerVolume Auto/Source/ExitClear Vision OSD Setting Basic and simple instruction on the control keysLuminance Press Menu to display menuPress or to select Luminance, and press to enter Press or to select submenu, and press to enterPress or to adjust Backlight AdjustmentAdjust to Gamma1 Adjust to GammaImage Setup Press or to select Image Setup, and press to enterAdjust picture Clock to reduce Vertical-Line noise PhaseAdjust Picture Phase to reduce Horizontal-Line noise Adjust picture sharpnessColor Setup Press or to select Color Setup, and press to enterColor setup Disable or Enable Full Enhance ModeDisable or Enable Nature Skin Mode Disable or Enable Green Field ModePicture Boost Press or to select Picture Boost, and press to enterAdjust Frame Size Adjust Frame BrightnessAdjust Frame Contrast Adjust Frame horizontal PositionOSD Setup Press or to select OSD Setup, and press to enterAdjust the horizontal position of Adjust the vertical position of OSDTimeout Adjust the OSD TimeoutExtra Press or to select Extra, and press to enterHDMI 1/HDMI LED Indicator ExitDriver Monitor DriverWindows 1.Start Windows5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 7.Click the “Driver” tab 9. Select Let me pick from a list of device drivers on my computer13. Close all open windows and remove the CD 2. Click Personalization and then Display Settings 3. Click Advanced Settings5. Click Update Driver... in the Driver tab 8. Select your monitor model and click on the Next button1. Start Windows XP 2. Click on the Start button and then click on Control Panel3. Select and click on the category ‘Appearance and Themes’ 4. Click on the Display Item5. Select the Settings tab then click on the Advanced button 7. Click on the Driver tab and then click on Update Driver... button6. Select Monitor tab If the Properties button is active, click on Properties button12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Saver Screen+ Troubleshoot Problem & QuestionPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active Specification General SpecificationPreset Display Modes RESOLUTIONSTAND HORIZONTALSignal Name Pin AssignmentsPin No Plug and Play Plug & Play DDC2B FeatureRegulation FCC NoticeWEEE Declaration Service Warranty Statement for EuropeInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil USA http//us.aoc.com/support/findservicecenter ARGENTINA http//ar.aoc.com/support/findservicecenterCHILE http//cl.aoc.com/support/findservicecenter COLOMBIA http//co.aoc.com/support/findservicecenter