AOC i2353 manual Service, Warranty Statement for Europe

Page 55

Service

Warranty Statement for Europe

LIMITED THREE-YEAR WARRANTY* AOC Color Monitors sold within Europe

AOC International (Europe) GmbH warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase. During this period, AOC International (Europe) GmbH will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. The defective products that are replaced become the property of AOC International (Europe) GmbH.

If the product appears to be defective, please contact your local dealer or refer to the warranty card when attached to the product.

Deliver the product freight pre-paid, along with the dated proof of purchase, to the AOC Authorized Service Center. If you cannot deliver the product in person:

Pack it in its original shipping container (or equivalent)

Put the RMA number on the address label

Put the RMA number on the shipping carton

Insure it (or assume the risk of loss/damage during shipment)

Pay all shipping charges

AOC International (Europe) GmbH is responsible neither for any damage or loss during inbound transport damage nor to inbound product that was not properly packaged.

AOC International (Europe) GmbH will pay the return shipping charges within one of the countries specified within this warranty statement. AOC International (Europe) GmbH is not responsible for any costs associated with the transportation of product across international borders. This includes the international border within the European Union.

*This limited warranty does not cover any losses or damages that occur as a result of Shipping or improper installation or maintenance

Misuse

Neglect

Any cause other than ordinary commercial or industrial application

Adjustment by non-authorized source

Repair, modification, or installation of options or parts by anyone other than an AOC Authorized Service Center

Improper environment

Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other irregularities

This limited warranty does not cover any of the product firmware or hardware that you or any third party have

55

Image 55

Contents Page Cleaning SafetyPower InstallationWarranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil National Conventions SafetyPower Installation Cleaning Other Adaptor SetupContents in Box Power Cable Analog Cable HDMI CableSetup Stand & Base Adjusting Viewing Angle 1 2 3 4 Connecting the MonitorWall Mounting 1 Click START AdjustingSetting Optimal Resolution Windows Vista6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings5 Double click DISPLAY Windows XP2 Click SETTINGS 3 Click CONTROL PANEL 4 Click Appearance and Themes For Windows XP7 Set the resolution SLIDE-BAR to 1920 by Windows ME/20004 Double click DISPLAY Auto/Source/Exit HotkeysPower VolumeClear Vision Basic and simple instruction on the control keys OSD SettingPress or to select submenu, and press to enter LuminancePress Menu to display menu Press or to select Luminance, and press to enterAdjust to Gamma Press or to adjustBacklight Adjustment Adjust to Gamma1Press or to select Image Setup, and press to enter Image SetupAdjust picture sharpness Adjust picture Clock to reduce Vertical-Line noisePhase Adjust Picture Phase to reduce Horizontal-Line noisePress or to select Color Setup, and press to enter Color SetupDisable or Enable Green Field Mode Color setupDisable or Enable Full Enhance Mode Disable or Enable Nature Skin ModePress or to select Picture Boost, and press to enter Picture BoostAdjust Frame horizontal Position Adjust Frame SizeAdjust Frame Brightness Adjust Frame ContrastPress or to select OSD Setup, and press to enter OSD SetupAdjust the OSD Timeout Adjust the horizontal position ofAdjust the vertical position of OSD TimeoutPress or to select Extra, and press to enter ExtraHDMI 1/HDMI Exit LED Indicator1.Start Windows DriverMonitor Driver Windows5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 9. Select Let me pick from a list of device drivers on my computer 7.Click the “Driver” tab13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab4. Click on the Display Item 1. Start Windows XP2. Click on the Start button and then click on Control Panel 3. Select and click on the category ‘Appearance and Themes’If the Properties button is active, click on Properties button 5. Select the Settings tab then click on the Advanced button7. Click on the Driver tab and then click on Update Driver... button 6. Select Monitor tab12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Saver Screen+ Ghosting Shadowing Problem TroubleshootProblem & Question Power LED Is Not ONMonitor Is Stuck In Active General Specification SpecificationHORIZONTAL Preset Display ModesRESOLUTION STANDSignal Name Pin AssignmentsPin No Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Warranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil COLOMBIA http//co.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterARGENTINA http//ar.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter