AOC i2353 manual Regulation, FCC Notice

Page 53

Regulation

FCC Notice

FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

NOTICE :

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to correct such interference.

53

Image 53

Contents Page Power SafetyInstallation CleaningWarranty Statement for North & South America excluding Brazil ServiceWarranty Statement for Europe National Conventions SafetyPower Installation Cleaning Other Contents in Box SetupPower Cable Analog Cable HDMI Cable AdaptorSetup Stand & Base Adjusting Viewing Angle 1 2 3 4 Connecting the MonitorWall Mounting Setting Optimal Resolution AdjustingWindows Vista 1 Click START6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings2 Click SETTINGS 3 Click CONTROL PANEL 4 Click Appearance and Themes Windows XPFor Windows XP 5 Double click DISPLAY4 Double click DISPLAY Windows ME/20007 Set the resolution SLIDE-BAR to 1920 by Power HotkeysVolume Auto/Source/ExitClear Vision Basic and simple instruction on the control keys OSD SettingPress Menu to display menu LuminancePress or to select Luminance, and press to enter Press or to select submenu, and press to enterBacklight Adjustment Press or to adjustAdjust to Gamma1 Adjust to GammaPress or to select Image Setup, and press to enter Image SetupPhase Adjust picture Clock to reduce Vertical-Line noiseAdjust Picture Phase to reduce Horizontal-Line noise Adjust picture sharpnessPress or to select Color Setup, and press to enter Color SetupDisable or Enable Full Enhance Mode Color setupDisable or Enable Nature Skin Mode Disable or Enable Green Field ModePress or to select Picture Boost, and press to enter Picture BoostAdjust Frame Brightness Adjust Frame SizeAdjust Frame Contrast Adjust Frame horizontal PositionPress or to select OSD Setup, and press to enter OSD SetupAdjust the vertical position of OSD Adjust the horizontal position ofTimeout Adjust the OSD TimeoutPress or to select Extra, and press to enter ExtraHDMI 1/HDMI Exit LED IndicatorMonitor Driver DriverWindows 1.Start Windows6.Click the “Monitor” tab and then click the “Properties” button 4.Ckick on the “Change display settings” button5.Click the “Advanced Settings” button 9. Select Let me pick from a list of device drivers on my computer 7.Click the “Driver” tab13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab2. Click on the Start button and then click on Control Panel 1. Start Windows XP3. Select and click on the category ‘Appearance and Themes’ 4. Click on the Display Item7. Click on the Driver tab and then click on Update Driver... button 5. Select the Settings tab then click on the Advanced button6. Select Monitor tab If the Properties button is active, click on Properties button13. Click on the Finish button then the Close button 11. Click on the Open button, then click the OK button12. Select your monitor model and click on the Next button Windows ME i-Menu e-Saver Screen+ Problem & Question TroubleshootPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active General Specification SpecificationRESOLUTION Preset Display ModesSTAND HORIZONTALPin No Pin AssignmentsSignal Name Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Warranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil ARGENTINA http//ar.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterCHILE http//cl.aoc.com/support/findservicecenter COLOMBIA http//co.aoc.com/support/findservicecenter