Alesis NANOVERB-2 quick start Quickstart Guide English, Front Panel, Rear Panel, BOX Contents

Page 3

QUICKSTART GUIDE (ENGLISH)

1.Make sure all items listed in the Box Contents are included.

2.READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT.

3.Place the product in an appropriate location for operation.

4.Ensure high quality, shielded audio cables are used away from sources of electromagnetic interference.

FRONT PANEL

BOX CONTENTS

ƒNANOVERB 2

ƒPower Adapter

ƒQuickstart Guide

ƒSafety Instructions & Warranty Information Booklet

2 5 4 6 7

31

1.POWER LED – Light will illuminate once the unit is powered on

2.INPUT – Controls both the Left (Mono) and Right channel analog input signal level

3.SIGNAL LED – LED will light up if the signal level is too high which may cause distortion. If this occurs, turn down the Input control knob and/or reduce the output level from your instrument source

4.OUTPUT – Adjusts the analog output signal level

5.MIX – Adjusts the balance between the incoming "dry" signal and the effect-processed signal. When this knob is turned to the far left, no processed signal will be heard. When the knob is turned to the middle position, an equal mix of the dry and processed signal will be heard. When the knob is turned to the far right, only the processed signal will be heard

6.EFFECTS SELECTOR – Select one of the 16 factory presets with this knob

7.PROGRAM – This will switch between different variations of the effect

REAR PANEL

8 11 10 10 9 9

8.POWER CONNECTOR – Plug the included AC adapter here (9v AC 500mA)

9.INPUT – Connect the ¼” unbalanced inputs to your source, such as Aux Sends on a mixer. For mono sources, just connect to the Left (Mono) input on the NANOVERB 2

10.OUTPUT – Connect the ¼” unbalanced outputs to an Aux Return on a mixer, powered speakers, or amplifer input

11.BYPASS – Attach a momentary (non-latching) footswitch to this 1/4" phone jack. When the footswitch is pressed, the NANOVERB 2 will bypass the effects and only the dry signal will pass through the unit. If the footswitch is pressed again, effects will continue to output

3

Image 3
Contents Guida Rapida Quickstart GuideGuía DE Inicio Rápido Guide Dutilisation RapidePage Front Panel Read Safety Instruction Booklet Before Using the ProductBOX Contents Quickstart Guide EnglishTypical Applications Powering UPSetup Setting Mixer AUX SEND/RETURN LevelsPreset EffectsParameter Range Symptom Cause Solution Troubleshooting GuideContenido DE LA Caja Guía DE Inicio Rápido EspañolPanel Frontal Panel TraseroEncendido InstalaciónAplicaciones típicas 30-650 ms EfectosDescripción Parámetro RangoSíntoma Causa Solución Guía DE Solución DE ProblemasContenu DE LA Boîte Guide D’UTILISATION Simplifié FrançaisPanneau Avant Panneau ArrièreConfiguration DémarrageApplications standards 30 à 650 ms EffetsDescription Paramètre PlageGuide DE Dépannage Symptôme Cause SolutionContenuti Della Confezione Guida Rapida ItalianoPannello Anteriore Pannello PosterioreConfigurazione DEI Livelli AUX SEND/RETURN DEL Mixer AccensioneApplicazioni tipiche Parametro Gamma EffettiRisoluzione DI Problemi SintomoCausa Soluzione Rückseite Ausgang Steuert den analogen AusgangssignalpegelSCHNELLSTART-ANLEITUNG Deutsch VorderseiteInbetriebnahme Mixereinstellungen FÜR AUX SEND-/RETURN-PEGELEinsatzmöglichkeiten Parameter Bereich EffekteFehlersuche Symptom Ursache LösungInput 51-0357-C