Denso BHT-7500, BHT-103 manual Message, Reason, Solution, Reference Tech Note

Page 62
Manual background

Error Message Resolution Guide

Message

Reason

Solution

Reference Tech Note

User Count Exceeded.\n Session

Possible authorization issue.

Verify that you have the correct number of

---

Ended;

 

licenses for the number of Mobile Units

 

 

 

you are using.

 

Primary Unavailable\nTrying Alternate;

First Host IP address not available

Verify the host address.

---

 

trying the remaining addresses in

 

 

 

the Host list.

 

 

APMAC.DAT Error\nSession Ended; Access point Media Access Control error.

Most likely a range, access point, radio,

T1113, T1114, T1161,

host or network issue. Troubleshoot the

T1171, T1187 and

customer’s environment.

T1194

MUIP.DAT Error\nSession Ended;

Mobile Unit IP Error.

Most likely a Mobile Unit network setting

T1113, T1114, T1161,

 

 

issue. Troubleshoot the customer’s

T1171, T1187 and

 

 

environment.

T1194

Missing Subnet IP\nSession Ended;

Mobile Unit IP Netmask Error.

Most likely a Mobile Unit network setting

T1113, T1114, T1161,

 

 

issue. Troubleshoot the customer’s

T1171, T1187 and

 

 

environment.

T1194

Error Opening File;

File is missing.

Verify that the configuration files are on the

---

 

 

Mobile Unit. Or perhaps there is a

 

 

 

hardware failure.

 

Telnet API\nnot found;

Program files are missing.

Battery Low Warning\n\nReplace

Not enough power to operate the

Battery Soon;

Mobile Unit.

No Host List.\nPress any key\nTo Edit

Have not configured your target

Host IP's;

hosts.

Unable to Allocate\nFont Memory;

Mobile Unit does not have enough

 

memory to load the fonts.

Reload program files.

---

Replace the battery with a fully recharged

---

battery.

 

Configure the target host IP addresses.

---

Reduce the fonts in use or expand the

---

memory in the Mobile Unit.

 

4-6

Supported Equipment Manual March, 2006

Image 62
Contents Supported Equipment Manual Production Copyright 1996 - 2006 by Connect, IncTrademarks Configuring the Terminal for Download Running Setup from a Download FileInstallation………………… This page is intentionally blank Descriptions Chapter 1 IntroductionRelease Notes Pictures BHT-7500 BHT-103Setup Requirements AccessoriesSupported Equipment Manual March Downloading From the WEB Chapter 2 Terminal SetupRunning Setup from a Download File Click on Next to begin the installation process InstallationThe InstallShield wizard runs and presents the following screen Terminal Setupa. To reboot the system immediately, click on Finish Toolbar Running the ManagerMenu Bar Configuring the Manager Quick StartSetting Terminal Model and COM Port For the purposes of this example, the name is vt220 Saving the ConfigurationClick File and Save As. Enter a name for this configuration Command Mode Safe Boot Configuring the Terminal for DownloadConnecting the Cradle Downloading EX3 FilesPress 2 H. Parity and move cursor to On Press 3 Linkup Time and move cursor to Press 1 for Basic Mode settings, and cursor to Optical The following screen will appear Choose OK at the prompt above Errors in System Mode DOWNLOAD FILE OUT OF MEMORY RETRY? 1. YES 2. NO 2-14The current download will exceed the maximum of 80 files in the memory 1 EXECUTE PROGRAM 2 DOWNLOAD 3 UPLOAD 4 SET SYSTEM 5 TEST 6 VERSION Setting the Default ExecutableTwin Client 1991-2006, Connect, Inc Keypress to Continue 7 FTP 8 RFStarting a Telnet Session Standard Setup Setup Using Twin Client ManagerHard is the same as Soft except the viewing keys are disabled 5250 Settings Hard is the same as Soft except the viewing keys are disabled 3270 Settings Hard is the same as Soft except the viewing keys are disabled Edit Server/Host IPs Terminal Setup Using Twin Client MenusEdit Mobile Unit IP Edit License Key Switch Client ModesSetting Default Executable Run Site SurveyAuthorizing PowerNet Authorized Terminals Add Licenses Enter the additional license’s authorization code and click on OK Transfer Authorization Click on OK when finished Click on the Close button when finished ListingClick on the Listing button to view authorization codes issued Codabar Start/Stop Number Chapter 3 Keypad Configuration Keypad Configuration BHT-7500Keypad Figures BHT-7500 VT KeyboardKeytop F5 x ‘3270 Keyboard sreq5250 Keyboard Keypad Table BHT-7500 right parenthesis BS C SF PW BHT-103M1 M2 7 8 4 5 1 2 BHT-103uppercase character screen lowercase character screenF9-F16 screen VT emulation 5250 emulation3270 emulation Note The 8 keys above are specific to 5250 emulationSupported Equipment Manual March 3-14 Down Left Up Right 3-16 Reason Chapter 4 Error Message Resolution GuideMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech NoteReason SolutionMessage Reference Tech Note