Micro Star Computer MS- 9130 v1.x Power Management Setup, SuspendMode, AC Loss Auto Restart

Page 54

MS-9130 Workstation Mainboard

Power Management Setup

SuspendMode

If system activity is not detected for the length of time specified in this field, all devices except CPU will be shut off. Settings: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 12 Min, 20 Min, 30 Min, 40 Min, 1 Hour.

AC Loss Auto Restart

This item specifies whether your system will reboot after a power failure or interrupt occurs. Available settings are:

Off

Leaves the computer in the power off state.

On

Leaves the computer in the power on state.

Former-stsRestores the system to the status before power failure or interrupt occurred.

IRQ/EventActivityDetect

Press <Enter> and the following sub-menu appears:

3-18

Image 54
Contents K8T Master2-FAR Series Version G52-S9130X1FCC-A Radio Frequency Interference Statement Copyright Notice Revision HistoryRevision Revision History Date V1.0 First release July Safety Instructions 使 用 者Contents Bios Setup Appendix A. VIA VT8237 Serial ATA RAID Introduction Getting Started Chipset Mainboard SpecificationsTarget Market Segment MainMemorySlots Power Management FeaturesDimension NetworkingMainboard Layout DDRMSI Special Features Core CenterTop-sideUsermode/Automode Left-side Current system statusRight-side PC hardware status during real time operation MSIRemindsYouHardware Setup Quick Components Guide JPWR1Central Processing Unit CPU CPU Installation Procedures for Socket Installing the CPU heatsink/cooler Fan powerInstalling DDR Modules MemoryMemory Population Rules Power Supply SSI 12V Power Connector JPWR2SSI 24-Pin Power Connector JPR1 ATX 20-Pin Power Connector ATX1 SSI 8-Pin Power Connector JPWR1 ATX 12V Power Connector JPW1Mouse Connector Back PanelView of the Back Panel Keyboard Connector Serial Ports COM1 & COM2USB Ports RJ-45 LAN Jack Giga-bit LANParallel Port Connectors Floppy Disk Drive Connector FDD1Hard Disk Connectors IDE1 & IDE2 Fan Power Connectors CFAN1/2, SFAN1/2, NBFAN1 LCD Panel Connector JLCD1Optional Serial ATA cableconnect to the hard disk devices Front Panel Connectors JFP1 & JFP2 JFP1 Pin DefinitionFront Panel Audio Connector JAUD1 JAUD1Front USB Connectors JUSB1 & JUSB2 Chassis Intrusion Switch Connector JCI1IrDA Infrared Module Header JIR1 Scsi LED Connector J7 CD-In Connector JCD1Aux Line-In Connector JAUX1 Jumpers Clear Cmos Jumper JBAT1PCI Peripheral Component Interconnect Slots SlotsAGP Accelerated Graphics Port Slot PCI Interrupt Request RoutingBios Setup Entering Setup Control KeysSub-Menu Getting HelpMainMenu General Help F1Main Menu Set Supervisor Password Load Fail-Safe DefaultsLoadOptimizedDefaults Set User PasswordStandard Cmos Features HaltOn Base/Extended/TotalMemoryQuick Power On Self Test Advanced Bios FeaturesHard Disk Boot Priority Virus WarningBoot Up NumLock Status 1st/2nd/3rd Boot DeviceBoot Other Device Security OptionVideoBIOSShadow MPS Version Control For OSDDR Timing Setting by Advanced Chipset FeaturesDRAMConfiguration Current FSB Frequency, Current Dram FrequencyAGPMode AGP & P2P Bridge ControlAGP Aperture Size AGP Driving ControlAGP Master 1 WS Read PCI Delayed TransactionAGP Master 1 WS Write LDT & PCI Bus ControlVIAOnChipIDEDevice IDE DMA transfer accessIntegrated Peripherals Serial ATA controllerPrimary/Secondary Master/Slave Ultra DMA IDEPrefetchModePrimary/Secondary Master/Slave PIO IDEHDDBlockModeUSB OnboardLanBootROMUSB Controller USBKeyboard/MouseSupportPower Status Led Parallel Port ModeEPP Mode Select Onboard Serial Port 1/2AC Loss Auto Restart Power Management SetupSuspendMode IRQ/EventActivityDetectVGA, LPT & COM, HDD & FDD, PCI Master PowerOnbyPCICardRTC Alarm Resume Modem Ring ResumePrimaryINTR IRQ3~IRQ15Reset Configuration Data PNP/PCI ConfigurationsPNP OS Installed Assign IRQ For VGA/USBPC Health Status ShutdownTemperatureSmart CPU Fan1/CPU Fan2/SYS Fan Temperature Case Open WarningCPU Fan1/CPU Fan2/SYS Fan Tolerance Value SpreadSpectrum Frequency/Voltage ControlAuto Detect PCI Clk CPU ClockLoad Fail-Safe/Optimized Defaults Set Supervisor/User Password About Supervisor Password & User PasswordAppendix a VIA VT8237 Serial ATA RAID Introduction Introduction Capacity BenefitsRAID 0 Striping RAID 1 MirroringBios Configuration Create Disk Array MS-9130 Workstation Mainboard MSIRemindsYou Delete Disk Array Create and Delete Spare Hard Drive View Serial Number of Hard Drive Duplicate Critical RAID 1 Array Power off and Check the Failed Drive Rebuild Broken RAID 1 ArrayDestroy the Mirroring Relationship Choose Replacement Drive and Rebuild Continue to bootInstalling RAID Software & Drivers Existing Windows XP Driver InstallationConfirming Windows XP Driver Installation Installation of VIA Sata RAID Utility MS-9130 Workstation Mainboard Using VIA RAID Tool MS-9130 Workstation Mainboard VIA VT8237 Serial ATA RAID Introduction MS-9130 Workstation Mainboard