Matsushita CF-18NHHZXBM service manual Display Unit, Assembly of LCD Front Case

Page 33

7.2.5.Assembling the Anntena Cover, the Tablet Latch Cover and the LCD Rear Case

1. Fix the LCD Rear Case using the 10 Screws <X> and the

2 Screws <W>.

<X>

2.

Attach the Antenna Covers and the Tablet Latch Cover to

 

the Display Unit.

3.

Tighten the 8 Screws <V> on the back of the Display Unit.

4.

Turn the Display Unit over, and tighten the 8 Screws. <V>

Screws <V> : DRQT26+E5FKL

Screws <W> : DXYN3+J10FNL

Screws <X> : DXYN2+J6FNL

<X>

<X><X> <X>

Antenna Cover<V>

<V>

<V>

<V>

<V> <V>

<V>

<V> <V> <V>

<W> LCD Rear Case <W>

<X>

<X><X> <X> <X>

<V>

<V> <V>

<V>

<V> Antenna Cover

<V>

Tablet Latch Cover

 

!Assembly of LCD Front Case

LCD Front Assy

Magnet Assy

0~0.5mm

Magnet Tape 0~1mm Magnet

–1mm(Both on the top and the side)

Be free of overhang..

Be free of overhang..

Be free of overhang.

TS Tape

Note for attachment

Ensure it does not come over the display part. Don’t get into a LCD indication range.

Attach and apply the load 30 to 40N (3.0 to 4.0 Kgf).

Position of pasting TS Tape. 0~0.5mm

0~0.5mm

Place this to the ribs. 0~0.5mm

7-14

Image 33
Contents CF-18 For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Basic Procedure Diagnosis ProcedureTroubleshooting Error Diagnosis by Checking Beep Signal Sound Table of errors classified by beep soundsOutline of Post Stuck key 02F4 Eisa Cmos not writable Preparation EquipmentSelf Diagnosis Test Speaker Test Vesa Mode TestCPU A20 Gate Test Cache ON/OFF TestPeripheral Test LAN Test Modem Test Wireless LAN TestTest Selection End of test Test classification Screen display test items Contents Error Messages and TroubleshootingPCB CN880 TouchScreen Panel Removing the Battery Pack and HDD Pack Removing the Touch Pad and Key- boardHDD FPC Removing the Rear Cabinet Removing the Speaker Angle and Dimm LidKBD FPCRemoving the Audio PCB Removing the DU Lid Unit Wireless Module Port PCB and ModemRemoving the SD PCB DU LIDRemoving LED PCB and Switch Removing the Main PCB and Lith- ium BatteryRemoving the PAD PCB and I/O Removing the CPU Heat PlateRemoving the Display unit Removing the LCD Rear Case Removing the LCD HingeLCD Removing Inverter PCB and LCD Removing the Each Cover Unit Setting up the LCD Unit Reassembly InstructionsSafety Working Touch Screen Assy Assembly of Touch Screen Applicable Model Touch Screen ModelGlass Assy Assembly of Glass Applicable Model Digitizer ModelGprs Line processing of Antenna CableSetting up the LCD Hinge Assembly of LCD HingeCable Hold Plate ScrewY ANT Cable Line processing of Antenna Cable and LCD CableHIinge Cover LCD CableDisplay Unit Assembly of LCD Front CaseAssembly of LCD Rear Case Applicable Model Digitizer Model ANT Cover Assembly of Tablet Latch Cover and Antenna CoverAssembly of Display Unit Setting the Display UnitModem Cable Setting the CPU Heat PlateSetting the LED PCB and the Switch PCB Assembly of the LED PCB and the Switch PCBPET Tape Assembly of PAD PCB Setting the PAD PCB and the I/O PCBPutting of the PAD Insulation Sheet Assembly of TOP Case AssyLine Processing of the Antenna Cable Setting the Main PCB and the Lithium BatteryPass the Lead Wire through the notch of the Board Line Processing of the Lithium BatteryLine Processing of Main Unit CN3Assembly of SD PCB Setting the SD PCBAssembly of the Port PCB Setting the Wireless Module, the Port PCB, and the ModemCable Line Processing of the Wireless Module,Port PCB and ModemScrew DU Sponge aAssembling the DU Lid Unit Setting the Audio PCBPutting of the Sheet Mm width x 5.5 cmSetting the Rear Cabinet Displacement Setting the Speaker and Dimm LitSetting the Touch Pad and the Keyboard KBD Waterproof Sheet R LCD Cushion SheetKB CNT Hole CushionKeyboard KBD Tape Putting of the Palm Rest AssyScrew Screw Screw KBD PlateL ScrewAssembly of the HDD Assy Setting the Battery Pack and the HDD PackRGB Assembling the Each CoverExploded View BT1 E42 K409 K210 K200-30 K211 K200-30-4 K200-30-35 K200-30-35-1 K220 Screw tightening torque Description QTY Wireless LAN ModulePCB, Main RTL PCB, Audio RTLPCB, Wide Area AUX Antenna RTL DFJK13T024DB FFC, PADDFJS977ZA CABLE, Wide Area AUX ANT. Brown DL3U7B482AAA PCB, SD RTLPower SW Knob DFHR3551YA Coin Battery SheetDFHR3262ZA Modem Tape DFHR3301YA Mini PCI Card SheetTablet Latch Assy TOP Case AssyBatt LID Assy DFBH3030ZA LID HingeDFHR3630ZA TS FPC Spacer DFHR3477ZA Spacer BDFHR3674YA TS Tape DL3DV0180AAA TS Panel AssyDXYN2+J18FNL Screw DXYN2+J12FNL ScrewDRHM0061ZA Screw DXYN4+J8FNL ScrewMain PCB RTC BatteryEEFCD0D151ER Page Page Page Page EEFCX0D331R EEFCD0D101EREEFCX0D221R EEFUD0J151ER EEFCX0J101R EEFCX0G151R ConnectorEEFCD0G101ER EEFCD0J470ERDEDRB081L20 Diode IC, USB Power ControlFUSE, 5A FUSE, 2AIC, Regurator IC, MiconIC, 1 Gate Logic IC, Gate Logic DA2205IDBLET IC, Bipolar LogicDDAZS100MT3T Inductor Poly SWTransistor DETA144EETL Transistor ERJ2RKF27R4X Transistor ERJ2GEJ681XERJ2RKF54R9X ERJ2RKF39R2XERJ2GE0R00X RESISTOR, 1/16W, 0Ω ERJ2GEJ103X RESISTOR, 1/16W ERJ2RKF80R6X RESISTOR, 1/16WERJ2GEJ101X ERJ2GEJ222XResistor Array ERJ2RKF1501X ERJ2RKF1002X RESISTOR, 1/16W, 10KΩERJ2GEJ390X ERJ2RKF2550XERJ2GEJ102X RESISTOR, 1/16W, 1KΩ ERJ2GEJ2R2XERJ2RKF49R9X ERJ2RKF4750X ERJ2GEJ330XERJ2GEJ1R0X RESISTOR, 1/16W, 1Ω ERJ2GEJ104XDEARA8AJ103M Resistor Array ERJ2RKF22R6XERJ2GEJ472X ERJ2GEJ203X RESISTOR, 1/16W, 20KΩERJ2GEJ181X ERJ2GEJ473X RESISTOR, 1/16W, 47KΩERJ2GEJ221X ERJ2GEJ471XERJ2GEJ474X ERJ2RKF1302X RESISTOR, 1/16W, 13KΩERJ2RHD752X ERJ2RKF2002X RESISTOR, 1/16W, 20KΩERA3YKB104V ERJ2RHD302X RESISTOR, 1/16W, 3KΩERA3YEB333V RESISTOR, 1/16W, 33KΩ TranceIC, Audio AMP IC, AC97 CodecERJ2GEJ103X RESISTOR, 1/16W, 1KΩ ERJ2GEJ273X RESISTOR, 1/16W, 27KΩEZASCE101M Capacitor Array Connector DFJS830YAERJ2RKF75R0X IC, Flat PAD ControllerERJ2GEJ103X RESISTOR, 1/16W, 10KΩ ERJ2GEJ822XEVQPLDA15 LEDERJ6GEYJ101V ERJ2GEJ303X RESISTOR, 1/16W, 30KΩ