Minuteman UPS ED6000T, ED6200T user manual

Page 20

7.1.21Looking from the front of the UPS on the left-hand side (FIG. 4), disconnect the battery negative (Black) wire. Place a piece of electrical tape over the end of battery negative (Black) wire.

7.1.22Disconnect battery jumper “A” and place a piece of electrical tape over the end of battery jumper wire “A”.

7.1.23Disconnect all of the battery jumper wires.

7.1.24Remove the battery-retaining bracket retaining screws.

7.1.25Remove the battery-retaining brackets.

7.1.26Remove the defective batteries and set aside.

7.1.27Install the new batteries in the same position as the original batteries.

7.1.28Re-install the battery-retaining brackets.

NOTE: DO NOT pinch the battery wires between the batteries and the battery- retaining brackets.

7.1.29Re-install the battery-retaining bracket retaining screws.

7.1.30Observer polarity. Reconnect all of the battery jumper wires.

7.1.31Remove the piece of electrical tape from the end of battery jumper wire “A”. Observer polarity. Reconnect battery jumper wire “A”.

FIG. 4

7.1.32Back to the right-hand side of the UPS (FIG. 3), remove the piece of electrical tape from the end of battery positive (Red) wire. Observer polarity. Reconnect the battery positive (Red) wire.

NOTE: Some sparking might occur, this is normal.

7.1.33Re-install the side panels and the retaining screws. (FIG. 2)

7.1.34Re-install the top cover and the retaining screws. (FIG. 1)

7.1.35Reconnect all of the communications and network cables.

NOTE: If you are using an External Battery Pack, reconnect the all of the battery cables to the UPS and the Battery Pack (s) rear panels. Turn ALL of the DC circuit breaker (s) on the rear panel of the Battery Pack (s) to the On position.

7.1.36Turn the utility power circuit breaker at the service panel to the On position.

7.1.37Turn the input circuit breaker on the rear panel of the UPS to the On position.

7.1.38Turn On the equipment that is connected to the UPS.

7.1.39Press and hold the On Switch (on the front panel) for approximately 3- seconds, then release.

7.1.40The UPS system is now ready for the normal operation.

7.1.41Properly dispose of the old batteries at an appropriate recycling facility or return them to the supplier in the packing material for the new batteries.

36

37

Page 19 Page 21
Image 20
Page 19 Page 21
Contents ED6000T & ED6200T Parallel RedundantTable of Contents Important Safety Instruction An Important NoticeLife Support Policy FCC NoticeProduct Introduction EPO Controls and Indicators Installation and Operation Qualified Service Personnel onlyRear Panel UnpackingStorage Instruction Installation PlacementInstallation of the Caster Covers Wiring the Input and Output Connections AWGPage Operation and Setup Instructions Page It shows the UPS is providing power to the load It shows the Internal Temperature of the UPS System Page LED LCD Power Monitoring Software EPO Emergency Power Off PortCommunication Port, EPO Port and Option Cards RS232 Communication PortReplacing the Batteries Troubleshooting GuideService Personnel only Battery Replacement Procedure Page Regulatory Compliance SpecificationsPhysical Obtaining Service Limited Product WarrantyDeclaration of Conformity

ED6200T, ED6000T specifications

The Minuteman UPS ED6000T and ED6200T are robust uninterruptible power supply (UPS) systems designed to offer reliable protection for sensitive electronic equipment. These units stand out in the market for their enhanced features, advanced technologies, and exceptional performance.

The core design of the ED6000T and ED6200T integrates a pure sine wave output, ensuring compatibility with all types of devices, including sensitive electronics and critical infrastructure. This feature minimizes electrical distortion, providing protection against damage from power fluctuations. They deliver up to 6000VA and 6200VA of power respectively, making them suitable for small to medium-sized data centers, telecommunications equipment, and critical servers.

One key characteristic of these models is their comprehensive LCD display that provides real-time monitoring of UPS status, battery charge level, load percentage, and other essential diagnostics. This user-friendly interface makes it convenient for users to assess performance at a glance and manage their power protection strategies effectively.

Both models employ advanced battery management technologies, including Smart Battery Management that extends battery life through optimized charging cycles. This is crucial for maintaining reliability, especially in environments where power outages can be frequent and disruptive. The UPS units also feature an automatic voltage regulation (AVR) system that corrects minor voltage fluctuations, maintaining consistent output without switching to battery mode.

Additionally, the ED6000T and ED6200T incorporate the Minuteman Green Power UPS™ technology, designed to minimize energy consumption and reduce heat output, thus contributing to lower operational costs and environmental sustainability. With an energy-efficient design, they are not only financially beneficial but also eco-friendly.

Connectivity options are another highlight, as both models feature multiple outlets, including surge-protected and battery backup outlets, ensuring plenty of connections for various devices. They are equipped with USB and serial communication ports that allow for seamless integration with monitoring and management software, thereby enhancing their functionality in networked environments.

In conclusion, the Minuteman UPS ED6000T and ED6200T are powerful solutions for businesses seeking reliable power protection. With their pure sine wave output, advanced battery management, user-friendly interfaces, and energy-efficient designs, they represent a solid investment for safeguarding critical electronics against power interruptions.
Top Page Image Contents