PowerFile A3 manual Rack System Precautions, Media Library Generation 2 or Generation

Page 11

Introduction

3

Media Library (Generation 2 or Generation 3)

•PowerFile Media Library

•Rail Kit box containing:

•2 Outer Rails (Left and Right)

•2 Inner Rails (Left and Right) packed in Outer Rails

•Accessory box containing:

•Registration Card

•Product Information Brochure

•Warranty Card

•1 1394 FireWire Cable

•1 Power Cord

•2 Qualification Media Discs (Generation 3 only)

Note: Do not open the Media Library unit. There are no user-serviceable parts inside the unit. For service questions, please contact PowerFile Technical Support.

WARNING: Opening the cover of the Media Library unit may expose you to visible and invisible laser radiation. Avoid direct exposure to laser beam.

Rack System Precautions

The following safety requirements must be considered when the unit is mounted in a rack.

•The rack design should incorporate stabilizing features suitable to prevent the rack from tipping or being pushed over during installation or in normal use.

•When loading a rack with the units, fill the rack from the bottom up and empty from the top down.

•The maximum operating ambient temperature for the unit is 35°C (94° F). The rack design should take this into consideration.

•The system must be operated with low pressure rear exhaust installation (back pressure created by rack doors and obstacles not to exceed 5 pascals [0.5mm water gauge]).

Active Archive Appliance (A3) v6.5

PowerFile Confidential

Racking and Installation Guide

Image 11

Contents Racking and Installation Guide PowerFile, Inc Contents Installing the Media Library in a Back-to-Back Configuration Front Panel HDDs and LEDs Contents Related Documents About This GuidePurpose AudienceActive Archive Appliance A3 PowerFile Confidential Archive Engine Generation IntroductionThis Chapter A3 System Shipping ComponentsIntroduction Media Library Generation 2 or Generation Rack System PrecautionsElectrical Distribution System Precautions Unpacking the A3 System Preparing for InstallationPreparing for Setup Rack Mounting Considerations Choosing a Setup LocationDetermining the Archive Engine Model Installing the Archive EngineIdentifying the Rail Kit Hardware Installing the Archive Engine GenerationInstalling the Archive Engine M5 Spring Washer Archive Engine Generation Archive Engine Rail Assembly Generation Archive Engine Rail Assembly Close Up Generation Mounting the Archive Engine in the Rack Installing the Archive Engine Generation Attaching the Inner Rail Extensions Identifying the Rail Kit ComponentsArchive Engine Generation 2 Inner Rail Assembly Detail Attaching the Outer Rails Archive Engine Generation 2 Outer Rail Assembly DetailArchive Engine Generation 2 Extension Bracket Attaching the Extension BracketsArchive Engine Rack Assembly Installing the Archive Engine Installing the Archive Engine Front-mount Configuration Installing the Media Library in a Front-mount ConfigurationMedia Library Self-tapping Screws Setting Up the Front-mounted ChassisGetting Started Media Library Keyhole Screws Media Library Inner Slide Rails and Keyhole Screws Media Library Inner Slide Rail and Self-tapping Screws Installing the Outer Rails on the Front-mounted ChassisMedia Library Inner Slide Rail on Front-mount Configuration Mounting-bracket Flange Close Up Mounting-bracket Flanges on Outer RailMounting-bracket Flange Attached Outer Rail Installed in RackMedia Library Aligned with Rack Rails Installing the Chassis in the RackMedia Library Rail Latch Close Up Media Library Rail LatchAttaching the Media Library Feet Media Library in Front-mount ConfigurationMedia Library Feet Back-to-Back Configuration Installing the Media Library in a Back-to-Back ConfigurationPower Strip Requirements Rack SpecificationsBack-to-Back Configuration Setting Up the Front-mounted Chassis Media Library Keyhole Screws Media Library Inner Slide Rails and Keyhole Screws Setting Up the Rear-mounted Chassis Media Library Keyhole Screws Media Library Inner Slide Rails and Self-tapping Screws Installing the Inner Slide Rails on the Rear-mounted ChassisOuter Rail Front-mounted Chassis Inner Slide Rail Mounting-bracket Flanges on Outer Rail Mounting-bracket Flange Attached Installing the Outer Rails on the Rear-mounted Chassis Mounting-bracket Flanges on Outer Rail Mounting-bracket Flange Attached Installing the Chasses in the Rack Media Library Rail Latch Media Libraries in Back-to-Back Configuration Installing the Cache Expansion Unit Identifying the Rail Kit Components Mounting Bracket Attached to Fixed Rail Before You BeginAttaching the Mounting Brackets and Rails HDD Bays and LEDs Front Panel HDDs and LEDsConnecting the Archive Engine and Media Libraries Setting Up the A3 SystemArchive Engine Ethernet Jack Connections To connect the Archive Engine and Media LibrariesArchive Engine and Media Library Connections Cache Expansion Array Connectors Connecting Cache Expansion ArraysConnecting Two Cache Expansion Arrays to an Archive Engine Two Cache Expansion Arrays and Archive Engine Connections One Cache Expansion Array and Archive Engine Connections Connecting One Cache Expansion Array to an Archive EngineMedia Library Power Button Powering On the A3 SystemPowering On the Media Library Powering On the Cache Expansion ArrayArchive Engine Generation 1 Power Button and Alarm Button Powering On the Archive Engine GenerationCache Expansion Array Power Connectors Loading Qualification Media in Media Library Generation Archive Engine Generation 2 Power ButtonPowering Off the A3 System Contacting PowerFile 951-13035-04 A3 Racking and Installation Guide