PowerFile A3 manual Installing the Archive Engine, Determining the Archive Engine Model

Page 15

3

Installing the Archive Engine

In This Chapter

•Determining the Archive Engine Model

•Installing the Archive Engine (Generation 1)

•Installing the Archive Engine (Generation 2)

This chapter provides instructions for installing the Archive Engine, Generation 1 and Generation 2.

Note: The following installation procedures apply to standard Electronics Industries Association (EIA) racks. Non-EIA racks may not be able to support the Archive Engine. If you are using a non-EIA rack, PowerFile recommends that you secure the Archive Engine using slide rails, which are available from PowerFile Authorized Resellers.

Determining the Archive Engine Model

The Archive Engine server is provided in two models: Generation 1 and Generation 2. Depending on which model you have, the rack mounting and installation procedures will differ.

To determine the Archive Engine model, check the serial number of the server. The serial number can be found on a label located near the lower left corner on the top of the server.

•Generation 1 servers have a serial number that starts with S and has a total of 15 characters. Go to “Installing the Archive Engine (Generation 1)” on page 3–8for installation instructions.

•Generation 2 servers have a serial number that starts with K and has a total of 11 characters. Go to “Installing the Archive Engine (Generation 2)” on page 3–15for installation instructions.

Active Archive Appliance (A3) v6.5

PowerFile Confidential

Racking and Installation Guide

Image 15

Contents Racking and Installation Guide PowerFile, Inc Contents Installing the Media Library in a Back-to-Back Configuration Front Panel HDDs and LEDs Contents Related Documents About This GuidePurpose AudienceActive Archive Appliance A3 PowerFile Confidential Archive Engine Generation IntroductionThis Chapter A3 System Shipping ComponentsIntroduction Media Library Generation 2 or Generation Rack System PrecautionsElectrical Distribution System Precautions Preparing for Installation Preparing for SetupUnpacking the A3 System Rack Mounting Considerations Choosing a Setup LocationDetermining the Archive Engine Model Installing the Archive EngineIdentifying the Rail Kit Hardware Installing the Archive Engine GenerationInstalling the Archive Engine M5 Spring Washer Archive Engine Generation Archive Engine Rail Assembly Generation Archive Engine Rail Assembly Close Up Generation Mounting the Archive Engine in the Rack Installing the Archive Engine Generation Attaching the Inner Rail Extensions Identifying the Rail Kit ComponentsArchive Engine Generation 2 Inner Rail Assembly Detail Attaching the Outer Rails Archive Engine Generation 2 Outer Rail Assembly DetailArchive Engine Generation 2 Extension Bracket Attaching the Extension BracketsArchive Engine Rack Assembly Installing the Archive Engine Installing the Archive Engine Front-mount Configuration Installing the Media Library in a Front-mount ConfigurationSetting Up the Front-mounted Chassis Getting StartedMedia Library Self-tapping Screws Media Library Keyhole Screws Media Library Inner Slide Rails and Keyhole Screws Media Library Inner Slide Rail and Self-tapping Screws Installing the Outer Rails on the Front-mounted ChassisMedia Library Inner Slide Rail on Front-mount Configuration Mounting-bracket Flange Close Up Mounting-bracket Flanges on Outer RailMounting-bracket Flange Attached Outer Rail Installed in RackMedia Library Aligned with Rack Rails Installing the Chassis in the RackMedia Library Rail Latch Close Up Media Library Rail LatchAttaching the Media Library Feet Media Library in Front-mount ConfigurationMedia Library Feet Back-to-Back Configuration Installing the Media Library in a Back-to-Back ConfigurationPower Strip Requirements Rack SpecificationsBack-to-Back Configuration Setting Up the Front-mounted Chassis Media Library Keyhole Screws Media Library Inner Slide Rails and Keyhole Screws Setting Up the Rear-mounted Chassis Media Library Keyhole Screws Media Library Inner Slide Rails and Self-tapping Screws Installing the Inner Slide Rails on the Rear-mounted ChassisOuter Rail Front-mounted Chassis Inner Slide Rail Mounting-bracket Flanges on Outer Rail Mounting-bracket Flange Attached Installing the Outer Rails on the Rear-mounted Chassis Mounting-bracket Flanges on Outer Rail Mounting-bracket Flange Attached Installing the Chasses in the Rack Media Library Rail Latch Media Libraries in Back-to-Back Configuration Installing the Cache Expansion Unit Identifying the Rail Kit Components Before You Begin Attaching the Mounting Brackets and RailsMounting Bracket Attached to Fixed Rail HDD Bays and LEDs Front Panel HDDs and LEDsConnecting the Archive Engine and Media Libraries Setting Up the A3 SystemArchive Engine Ethernet Jack Connections To connect the Archive Engine and Media LibrariesArchive Engine and Media Library Connections Connecting Cache Expansion Arrays Connecting Two Cache Expansion Arrays to an Archive EngineCache Expansion Array Connectors Two Cache Expansion Arrays and Archive Engine Connections One Cache Expansion Array and Archive Engine Connections Connecting One Cache Expansion Array to an Archive EngineMedia Library Power Button Powering On the A3 SystemPowering On the Media Library Powering On the Cache Expansion ArrayPowering On the Archive Engine Generation Cache Expansion Array Power ConnectorsArchive Engine Generation 1 Power Button and Alarm Button Loading Qualification Media in Media Library Generation Archive Engine Generation 2 Power ButtonPowering Off the A3 System Contacting PowerFile 951-13035-04 A3 Racking and Installation Guide