POSIFLEX Business Machines PP3000 manual CE manufacturer, EC Council Directive 89/336/EEC of 3 May

Page 2

TM

WARRANTY AND EXCEPTIONS

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

For compliance with Federal Noise Interference Standard, this equipment requires a shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

CE manufacturer

Declaration of Conformity

(EC Council Directive 89/336/EEC of 3 May 1989)

This product has been designed and manufactured in accordance with the International Standards EN50081-1/01.92 and EN50082-1/01.92 following the provisions of the Electro Magnetic Compatibility Directive of the European Communities as of May 1989

Warranty Limits

Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.

About This Manual

This manual is aimed to assist the user to utilize the PP3000 series which is a series of POS printers delicately designed to work with either serial or parallel interface connection. This manual covers both operational and technical aspects. This manual is revised to cover also the Epson emulation commands and some frequently asked questions.

The manufacturer of the PP3000 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information through our web

site: http://www.posiflex.com.tw .

© Copyright Mustek Corp. 1997

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Mustek Corp. the publisher of this documentation.

The following terms used in this publication are trademarks or service marks of Mustek Corp. the publisher of this documentation: POSiFLEX; Mustek; PP3000 POS printer; POSiFLEX PST system. Other company, product and service names may be trademarks or service marks of others.

Image 2
Contents POS Printer Manual Rev.BEC Council Directive 89/336/EEC of 3 May Warranty LimitsCE manufacturer About This ManualPage Page Table of Contents Data Structure in Serial Interface · · · · · · · · · · Iii Other Control Codes · · · · · · · · · · · · · · · · · 7 Appendix C Page General Description Overview Model NumbersFeatures Unpacking Contents Basic MountingMounting printer to PST For Other System Cable ConnectionsLoading Ribbon Cartridge Cable connection examplesLoading ribbon cartridge Loading Paper OFFGrooves on paper guide shaft Removing The Roll Paper Putting spacer to roll paper shaftPower LED green On Line switchFeed switch Alarm LED redLocations of switches and LED’s Self Print TestSelf print sample Micro Feed Hexadecimal Dump ModeClear Print Buffer Validation PrintingOperation Method Validation printingPaper Format Printing FormatData Format Other ConsiderationsPeripheral Unit Drive Circuit Telephone jack and plug for peripheral unit driveChap OPERA… Block Diagram Circuit block diagramCircuitry Layout & Connectors Board layoutCN9 Printer power input connector Serial Interface Switch Jumpers & SwitchesJumper Setting Interface Select USA OFFON/ OFF DIP-SW Character code table DIP-SW ModeAddress selection for addressable mode #10 #11 #12 #13 #14 DIP-SW3Parallel Interface Switch DIP-SW1DIP-SW DTR Mode Data Structure in Serial InterfaceON/X-OFF Mode Mechanical errorStatus STX-ETX Mode RET Chap TECHN… Interface Parallel InterfaceBusy Serial Interface Peripheral Unit DriveFont Matrices Power SupplyOption List CaseCharacter size 15 CPI 12 CPI CPIWeight CommandsExternal Dimensions Operating EnvironmentCleaning Paper JAMTrouble Shooting Control Codes Hex Codes Function Star Compatible ModeControl Codes for Character Setting Control Codes for Line Spacing Control Codes for Page LayoutControl Codes for Graphics Printing Control Codes for Download CharactersBasic Reference Control Codes for Peripheral UnitsOther Control Codes Hardware Modification RequiredUnsupported Control Codes Reference Epson Models EmulatedCharacter Size/Font Matrices Supported Control CodesESC SP APP. a Star … Codes HEX/CONTROL 09 / HT Function Line feedCodes HEX/CONTROL 07 / BEL Codes HEX/CONTROL 0A / LFCodes HEX/CONTROL 0E / SO Codes HEX/CONTROL 0C / FFCodes HEX/CONTROL 0D / CR Codes HEX/CONTROL 0F / SIFunction Cancel inverted print mode Codes HEX/CONTROL 12 / DC2Codes HEX/CONTROL 18 / can Codes HEX/CONTROL 13 / DC3Codes HEX/CONTROL 14 / DC4 Codes HEX/CONTROL 19 / EM Function Immediate drive command for peripheral unitDefinition Range 1 ≤ n1 ≤ 127, 1 ≤ n2 ≤ Codes HEX/CONTROL 1A / SUBAPP. a Star … Codes HEX/CONTROL 1B 26 00 n1 n2 / ESC & 0 n1 n2 APP. a Star … Codes Definition Range 1 ≤ n ≤Codes HEX/CONTROL 1B 40 / ESC @ Function Initialize printer Codes HEX/CONTROL 1B 3A / ESCFunction Select 8 CPI character size Definition Range 0 ≤ n ≤ 85 Default n = Definition Range 1 ≤ n1 … nk ≤ 255, 1 ≤ k ≤Definition Range 1 ≤ n1 … nk ≤ 39, 1 ≤ k ≤ Function Select emphasized print modeFunction Cancel emphasized print mode Codes HEX/CONTROL 1B 45 / ESC ECodes HEX/CONTROL 1B 4B n1 00 / ESC K n1 Definition Range 1 ≤ n1 ≤Definition Range 1 ≤ n1 + 256 x n2 ≤ Function 8 dot single density bit imageCodes HEX/CONTROL 1B 4D / ESC M Definition Range 0 ≤ n ≤ 255 Default n =Detail Description Cancel bottom margin Codes HEX/CONTROL 1B 4F / ESC OFunction Select 12 CPI character size Definition Range 00H ≤ n ≤ 0AHCodes HEX/CONTROL 1B 50 / ESC P Codes Function Detail Description Cancel overline mode Detail Description Cancel vertical expanded character mode Definition Range 0 ≤ n ≤ right margin Function Set left marginCodes HEX/CONTROL 1C / FS Codes HEX/CONTROL 1E / RS Function Sound buzzer