Lincoln POWER-ARC 4000 manual What Happens in the Arc?, Welding arc

Page 27

B-12

OPERATION

B-12

 

 

 

The Power-Arc 4000 has a voltage output of up to 62 volts which can shock.

WARNING

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or electrode with skin or wet cloth- ing.

•Insulate yourself from work and ground.

•Always wear dry insulating gloves.

cannot be looked at with the naked eye without risking painful and possibly permanent injury. A very dark lens, specifically designed for arc welding must be used with the handshield or headshield whenever viewing the arc.

The arc melts the base metal and actually digs into it, much like water through a garden hose nozzle digs into the earth. The molten metal forms a pool or crater and tends to flow away from the arc. As it moves away from the arc, it cools and solidifies. Slag forms on top of the weld to protect it during cooling.

Covering

ENGINE EXHAUST can kill.

Solidified Slag

Electrode

Arc

• Use in open, well ventilated areas or vent exhaust outside.

•Do not stack anything on or near the engine.

MOVING PARTS can injure.

•Do not operate with doors open or guards off.

• Stop engine before servicing.

•Keep away from moving parts.

Only qualified personnel should install, use, or service this equipment.

The electric arc is made between the work and the tip end of a small metal wire, the electrode, which is clamped in a holder that is held by the welder. A gap is made in the welding circuit (see Figure 3) by hold- ing the tip of the electrode 1/16 - 1/8” (1.6-3.2mm) away from the work or base metal being welded. The electric arc is established in this gap and is held and moved along the joint to be welded, melting the metal as it is moved.

Arc welding is a manual skill requiring a steady hand, good physical condition, and good eyesight. The operator controls the welding arc and, therefore, the quality of the weld made.

Shielding Gases

Weld Metal

Base Metal

FIGURE 4 - The welding arc.

The function of the covered electrode is much more than simply to carry current to the arc. The electrode is composed of a core metal wire around which has been extruded and baked a chemical covering. The core wire melts into the arc and tiny droplets of molten metal shoot across the arc into the molten pool. The electrode provides additional filler metal for the joint to fill the groove or gap between the two pieces of the base metal. The covering also melts or burns in the arc. It has several functions. It makes the arc stead- ier, provides a shield of smoke-like gas around the arc to keep oxygen and nitrogen in the air away from the molten metal, and provides a flux for the molten pool. The flux picks up impurities and forms a protective slag. The principle differences between the various types of electrodes are in their coatings. By varying the coating, it is possible to greatly alter the operating characteristics of electrodes. By understanding the differences in the various coatings, you will gain a bet- ter understanding of selecting the best electrode for the job you have at hand. In selecting an electrode, you should consider:

1.The type of deposit you want, e.g., mild steel, stainless, low alloy, hardfacing.

2.The thickness of the plate you want to weld.

What Happens in the Arc?

Figure 4 illustrates the action that takes place in the electric arc. It closely resembles what is actually seen during welding.

The “arc stream” is seen in the middle of the picture. This is the electric arc created by the electric current flowing through the space between the end of the electrode and the work. The temperature of this arc is about 6000°F (3316°C) which is more than enough to melt metal. The arc is very bright, as well as hot, and

3.The position it must be welded in (downhand, out-of-position).

4.The surface condition of the metal to be welded.

5.Your ability to handle and obtain the desired electrode.

Four simple manipulations are of prime importance. Without complete mastery of these four, further attempts at welding are futile. With complete mastery of the four, welding will be easy.

POWER-ARC 4000

Page 26 Page 28
Image 27
Page 26 Page 28
Contents POWER-ARC California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionPrécautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyMaster Table of Contents for ALL Sections Technical Specifications POWER-ARC InstallationEngine Exhaust can kill Safety PrecautionsLocation and Ventilation StoringPRE-OPERATION Engine Service 8 HP Carb. Certified 9 HP Honda 9 HP Kool Bore Plus Power-Arc 4000 Typical Fuel ConsumptionMuffler Deflector Spark ArresterElectrical Output Connections Welding Cable ConnectionsCable Size and Length Plugs and HAND-HELD Equipment Auxiliary Power ReceptaclesCable Installation Machine GroundingCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the POWER-ARCGeneral Description Safety InstructionsOperation Operating InstructionsWelding Capability Operational Features and ControlsDesign Features Advantages Recommended ApplicationsGENERATOR/WELDER Controls Controls and SettingsGasoline Engine Controls Engine Operation Before Starting the EngineStarting the Engine Stopping the Engine Running the EngineBREAK-IN Period General Information Generator OperationTable B.3 Generator Power Applications Control Function / Operation Current Control Dial Welding OperationWelding Guidelines Material Thickness Electrode Type Size SettingStick Welding Welding arc What Happens in the Arc?Side view Correct Welding Position Correct Arc LengthCorrect Way to Strike An Arc Correct Welding SpeedDo the following Common MetalsTypes of Welds Use the followingWelding in the Vertical Position PenetrationFillet Welds Multiple Pass WeldsVertical-Down Welding Vertical-Up WeldingHardfacing To Reduce Wear How to Hardface the Sharp Edge Metal to Ground WearOverhead Welding Welding Sheet MetalCast Iron Plate Preparation Welding Cast IronLow Hydrogen Group Stable-Arc E7018 Selecting ElectrodesOut-of-Position Group AWS E6011 High-Speed Group AWS E6013Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Engine Adjustments MaintenanceRoutine and Periodic Maintenance Engine MaintenanceFigure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Table D.1 Engine Maintenance Parts PartHonda Figure D.5. Brush Removal and Replacement GENERATOR/WELDER MaintenanceFigure D.6. Major Component Locations HOW to USE Troubleshooting Guide TroubleshootingPossible Areas SymptomsTroubleshooting Engine requires service to head, head gasket, and/or valves Diagrams S25341 Wiring Diagram Power ARC 4000 Codes 10671Dimension Print Power ARC POWER-ARC POWER-ARC Precaucion Warnung
Top Page Image Contents