Lincoln POWER-ARC 4000 manual Machine Grounding, Plugs and HAND-HELD Equipment, Cable Installation

Page 13

A-6

INSTALLATION

A-6

 

 

 

Cable Installation

Install the welding cables to your POWER-ARC 4000 as follows. See Figure A.1 for the location of parts.

1.The gasoline engine must be OFF to install weld- ing cables.

2.Remove the 1/2 - 13 flanged nuts from the output terminals.

3.Connect the electrode holder and work cables to the weld output terminals. You can connect either cable to either terminal, since the POWER- ARC 4000 provides AC weld current.

4.Tighten the flanged nuts securely.

5.Be certain that the metal piece you are welding (the “work”) is securely connected to the work clamp and cable.

6.Check and tighten the connections periodically.

CAUTION

•Loose connections will cause the output termi- nals to overheat. The terminals may eventually melt.

•Do not cross the welding cables at the output terminal connection. Keep the cables isolated and separate from one another.

Lincoln Electric offers a welding accessory kit with the properly specified welding cables. See the ACCESSORIES section of this manual for more infor- mation.

MACHINE GROUNDING

Because the POWER-ARC 4000 creates its own power from its gasoline-engine driven generator, you do not need to connect the machine frame to an earth ground. However, for best protection

against electrical shock, connect a heavy gauge wire from the ground stud located on the bottom center of the output panel (see Figure A.1) to a suitable earth ground such as a metal pipe driven into the ground.

WARNING

Do not ground the machine to a pipe that carries explosive or combustible material.

When the POWER-ARC 4000 is mounted on a truck or a trailer, the machine gen- erator ground stud MUST be securely connected to the metal frame of the vehicle. See Figure A.1. The ground stud is marked with the symbol.

PLUGS AND HAND-HELD EQUIPMENT

For further protection against electric shock, any electrical equipment connected to the generator receptacles must use a three-blade, grounded type plug or an Underwriter’s Laboratories (UL) approved double insulation system with a two-blade plug. Lincoln offers an accessory plug kit that has the right type of plugs. See the ACCESSORIES section of this manual for details.

Ground fault protection is needed for hand held equipment.

WARNING

Never operate this machine with damaged or defec- tive cords. All electrical equipment must be in safe condition.

AUXILIARY POWER RECEPTACLES

The control panel of the POWER-ARC 4000 features two auxiliary power receptacles:

•A 20 amp, 120 volt duplex (double outlet) recepta- cle

•A 20 amp 240 volt simplex (single outlet) recepta- cle.

See Figure A.1.

Through these receptacles the machine can supply up to 4,000 rated continuous watts and 4,400 surge watts of single-phase AC power.

POWER-ARC 4000

Page 12 Page 14
Image 13
Page 12 Page 14
Contents POWER-ARC California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionPrécautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyMaster Table of Contents for ALL Sections Technical Specifications POWER-ARC InstallationLocation and Ventilation Safety PrecautionsStoring Engine Exhaust can killPRE-OPERATION Engine Service Muffler Deflector Power-Arc 4000 Typical Fuel ConsumptionSpark Arrester 8 HP Carb. Certified 9 HP Honda 9 HP Kool Bore PlusWelding Cable Connections Electrical Output ConnectionsCable Size and Length Cable Installation Auxiliary Power ReceptaclesMachine Grounding Plugs and HAND-HELD EquipmentCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the POWER-ARCOperation Safety InstructionsOperating Instructions General DescriptionDesign Features Advantages Operational Features and ControlsRecommended Applications Welding CapabilityGENERATOR/WELDER Controls Controls and SettingsGasoline Engine Controls Before Starting the Engine Engine OperationStarting the Engine Running the Engine Stopping the EngineBREAK-IN Period General Information Generator OperationTable B.3 Generator Power Applications Control Function / Operation Current Control Dial Welding OperationWelding Guidelines Material Thickness Electrode Type Size SettingStick Welding Welding arc What Happens in the Arc?Correct Way to Strike An Arc Correct Welding Position Correct Arc LengthCorrect Welding Speed Side viewTypes of Welds Common MetalsUse the following Do the followingFillet Welds PenetrationMultiple Pass Welds Welding in the Vertical PositionVertical-Down Welding Vertical-Up WeldingOverhead Welding How to Hardface the Sharp Edge Metal to Ground WearWelding Sheet Metal Hardfacing To Reduce WearCast Iron Plate Preparation Welding Cast IronOut-of-Position Group AWS E6011 Selecting ElectrodesHigh-Speed Group AWS E6013 Low Hydrogen Group Stable-Arc E7018OPTIONS/ACCESSORIES AccessoriesLincoln Electric Accessories Routine and Periodic Maintenance MaintenanceEngine Maintenance Engine AdjustmentsFigure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Part Table D.1 Engine Maintenance PartsHonda Figure D.5. Brush Removal and Replacement GENERATOR/WELDER MaintenanceFigure D.6. Major Component Locations HOW to USE Troubleshooting Guide TroubleshootingPossible Areas SymptomsTroubleshooting Engine requires service to head, head gasket, and/or valves Diagrams S25341 Wiring Diagram Power ARC 4000 Codes 10671Dimension Print Power ARC POWER-ARC POWER-ARC Precaucion Warnung
Top Page Image Contents