Q-See Computer Hardware manual Introduction Summarization

Page 5

 

 

Error! Use the Home tab to apply

 

 

 

标题 1 to the text that you want to

 

SuperDVR & H.264 Series Cards

 

appear here. Error! Use the Home

 

 

tab to apply 标题 1 to the text that

 

User Manual

 

 

 

you want to appear here.

 

1 Introduction

1.1 Summarization

Thank you for choosing our digital video capture cards.

4 Channel, 8 Channel and 16 Channel cards adopt H.264 compression format, and enable a maximum of 16 channels real-time surveillance in CIF resolution. Our cards are mature and cost-effective products that should be your ideal choices. They enable synchronous audio and video compression and transmission along with their powerful compression rate and network transmission function. They are widely used in banks, intelligent communities, traffic management units, medical systems, educational systems, armed forces and so on.

This manual is suitable for SuperDVR 6.2, which supports QSDT4PCRC, QSDT4PCRP, QSDT8PCRP, and QSPD4116 cards.

In this manual, you will learn how to install the hardware and driver (software), and how to setup the systems on this range of products. Please make sure your operations with the products are strictly in accordance with the manual, to maintain the stability of the digital surveillance systems.

The following are standard functions of these products:

•Schedule record mode

Users can choose any period in a day to record and set up record modes, i.e. sensor alarm record, motion detection record, manual record, Schedule Record.

•Motion detection mode

Motion detection areas are adjustable with a maximum 16 areas for each channel. Users can also set motion detection sensitivity for each channel. The system begins to record only when motion is detected is detected on the channel and after motion stops it will stop recording after a certain time period, which is adjustable by users.

•Sensor alarm record mode

The system has an external alarm which enables the system to support alarm input and output.

•Recycling record mode

Users can set recording storage sequence for HDD partitions. The recording storage will automatically switch to the next partition when the current one is full. If all the partitions are full and recycling record mode is enabled, the oldest recorded data will be covered by new data. Users can also set HDD minimum storage alarm. Then once the present storage

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Page Contents Error! Bookmark not defined Appendix 2.4 Other Questions Appendix2 Quick Start for UsingAppendix3 Function Tree Appendix 4.3 IE Client FunctionTreeIntroduction Summarization Page QSDT4PCRC/QSDT4PCRP Card System Requirements System RequirementsQSDT8PCRP QSDT8PCRP Card System RequirementsCard QSPD4116 PC Module QSPD4116 Card System RequirementsSystem Specifications QSDT4PCRC Card Hardware Hardware InstallationVideo Capture Card Hardware QSDT4PCRP Video Capture Card QSDT4PCRP Card HardwareDefinition of Audio and Video QSDT8PCRP Video Capture Card QSDT8PCRP Card HardwareCall Monitor interface is used to connect the spot monitor QSPD4116 Card Hardware11Audio Connector and Pins Definition Connect Audio Signal Alarm Board Hardware15H.264 Series Video Capture Card Installation Interface Install Video Capture Card Driver17Select Video Format ： Install driver first： Click ‘Finish’ ： Click ‘Next’23Installing the Software on Vista Display Control Panel Main Display InterfaceDisplay Control Panel Display ModesAuto Dwell Display Mode LoginCapture Urgent RecordRecord Modes Record SetupRecord Record Status Panel Record Status Panel & Alarm Output Status PanelMotion Detection Record Mode Manual Record ModeSensor Alarm Record Mode Recycling Recordings Schedule RecordingClick to enter the main setup interface System SetupBasic Configuration Caption and General Configuration Computer System Reboot Setup Video ConfigurationClick and enter the Motion Detection Configuration Motion Detection ConfigurationBy clicking ‘Clear’, you can clear all the selected areas Set Motion Detection AreaClear Motion Detection Area Schedule Configuration Schedule ConfigurationAlarm Triggering Conditions Configuration Motion Detection Alarm ConfigurationSystem can receive alarms from both local place and network Local Alarm Record Triggering ConfigurationAlarm Output Alarm RecordAuto Mail Function 12Auto Mail Setup Interface Edit Map Map Configuration15E-Map Edit View Map16View Cameras Protocol Setup P.T.Z Control ConfigurationClick and enter PTZ Configuration Address Communication address of P.T.Z device ID number Serial Ports SetupChange User rights Users ConfigurationClick to access the User’s Configuration area Delete User Add User23Confirm Delete User P.T.Z Control Interface T.Z ControlCamera Speed AdjustmentPreset and Group Select Search and Playback Interface Record Search & Playing BackPlaying Back and Control Record SearchPlaying Speed Controller Multiple Channel Playback Control Other Functions Recorded File BackupThen click ‘OK’ to play back Click and enter the following menuClick and the following window will appear Delete Recorded Files13Color Control Panel Capture PicturesBy clicking users can display print preview as shown below 15Print Setup17Example original size Image Zoom in/out19Example zoomed Remote Live Surveillance Remote Surveillance Server ConfigurationHigher quality setting Setting up Router for Internet AccessPort Forwarding Finding Router’s Public IP address It will give you instructions for your routerSuperDVR & H.264 Series Cards Page Advanced Options 10 Invalid Signature Accessing IE clientUnknown Publisher or Unsigned Program Error 11 Webcam install interface Button Focus closer Function of the main interface buttons Record playback and control Remote playback15 Remote backup Channel configuration window will appear Click and enter into the main setup interface Basic Configuration Camera setup Alarm setup configuration is show belowSchedule configuration Click icon to enter into alarm configuration as shown below Alarm configurationRecord setup Record configurationMotion configuration Click icon to access to Email configuration interface Email ConfigurationMail server setup 34 P.T.Z Configuration 8 P.T.Z ConfigurationPort Users can set port number Baud rate Protocol setupIntroduction to Mobile Surveillance Mobile SurveillancePage SuperDVR & H.264 Series Cards By Smart Phone with Symbian Operating System SuperDVR & H.264 Series Cards Internet ： It will show the camera after accessing successfully Appendix 2.2.1 Meanings of the indicator lights Appendix 2.1.1 Cannot Install the SuperDVR DriverAsked Questions Appendix 2.2.2 How do the different record modes work?Appendix 2.2.8 Why can’t I select more channels to backup? Appendix 2.2.4 How to set auto reboot functionAppendix 2.3.4 Why can’t I see the images? Appendix 2.3.1 How to monitor on the client-sideTIP Appendix 2.4 Other Questions Appendix 2.4.2 Why I can’t find the recorded files?Appendix 2.4.8 Precautions on changing system time Appendix 2.4.5 Why can’t I play back?Change can be made directly Appendix2 Quick Start for UsingAppendix 3.2 Troubleshooting Unsigned ActiveX controls’ see section Function Tree Appendix 4.2 System Configuration Tree Appendix 4.3 IE Client FunctionTree Appendix 4.4 Remote Playback Function Tree 103 See Product Warranty104
Top Page Image Contents