Rimage 360i manual Printing on hub without a stacking ring, Aligning the ink cartridges

Page 19
Tip: The image below shows a disc with no stacking ring.

Tip: The image below shows a disc with no stacking ring.

Tip: Rimage recommends that you set the inner diameter so that it is 1 mm greater than the actual measurement to prevent the ink from smearing. The inner diameter on Rimage media is 23 mm. Set the inner diameter field to 24 mm.

Operate the Rimage 360i

Printing on hub without a stacking ring

This functionality allows you to print on the full surface of a disc that has no stacking ring. If you print on areas of the disc where the surface is not suitable for printing, the ink can smear or run.

1.Navigate to Printing Preferences (refer to page 9).

2.Change mask settings.

a.Select the Mask Settings tab.

b.Select the Enable Masking checkbox.

c.In the Hub Area Settings box, select the Printing on Hub checkbox.

3.Measure the printable area and adjust the settings.

a.Measure the inner diameter of the printable surface.

b.In the Hub Area Settings, change the Outer Diameter and Inner Diameter settings to the value measured in step a before changing any other diameter settings.

c.In the Standard Area Settings, change the Inner Diameter to the same value used in step b.

4.After you have entered the correct measurements, select OK. The

Disc Color 360i Properties window closes.

Aligning the ink cartridges

For optimal print quality and maximum printing speed, use this procedure to align the ink cartridges.

1.Navigate to Printing Preferences (refer to page 9).

2.At the Rimage 360i, open the front cover.

3.Press the green (middle) button. The printer tray opens.

4.Align the ink cartridges.

a.From the Disc Color Printer 360i Printing Preferences window, select the Service tab.

b.Select the Service ToolBox button. The Rimage Service Toolbox window opens.

c.Select the Align Cartridges button. The Align Cartridges for Disc Color 360i dialog box opens.

d.To align the ink cartridges, follow the instructions in the Align Cartridges for Disc Color 360i dialog box.

e.To close the Align Cartridges for Disc Color 360i dialog box, select OK.

5.To close the Disc Color 360i Printing Properties window, select OK.

6.To close the printer tray, press the green (middle) button. The printer tray closes.

7.Close the front cover.

110808_C

13

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Rimage 360i User Guide Page European Headquarters Corporate HeadquartersCD and DVD Recording Software Disclaimer South America RimageNorth America EuropeMaintain the Rimage ContentsContents IntroductionRimage Operating System requirements IntroductionRequirements Software requirementsLabel design requirements Front View Identify the parts of the RimageIdentify the parts of the Rimage Pause button Rimage 360i ButtonsFunctionality Rimage 360i Project Status Indicator PSIImage NameFilter Cover Rear Cover Power Switch Power Cord Port USB Port Rear viewOperate the Rimage Powering on the RimagePausing the Rimage Operate the Rimage1. Open the input door Loading the discs3. Close the input door Navigating to Printing Preferences Accessing Printing Preferences through Windows Start menuAccessing Printer Preferences through CD Designer Select your printing preferencesAdding, editing, or deleting a watermark Setting the print qualityc. Select OK. The Digital Photography Options window closes Setting up color options Adjusting the ink volume used3. Turn Print in Grayscale on or off Standard Area Changing or enabling maskingPrinting on hub with a stacking ring Tip The image below shows a disc with a stacking ringAligning the ink cartridges Printing on hub without a stacking ringTip The image below shows a disc with no stacking ring Checking the ink levels Centering the image on the discMaintain the Rimage General CleaningCleaning the exterior Cleaning the ink cartridge nozzlesReplacing the fan filter Replace Consumablesa. Remove the cartridge and reinsert it Replacing the ink cartridges7. Close the ink cartridge access door c. If the problem persists, replace the cartridgeLearn More Rimage 360i SpecificationsLearn More Technical support and product updatesSafety information Safety precautionsProduct name Rimage Safety testingModel RAS17 Rimage 360i Limited 1 Year Warranty
Top Page Image Contents