Teledex IP250DVoIP Unpacking the IP250D, Connecting the Handset, Connecting a PC to the IP250D

Page 8

INSTALLING THE IP250D

2.2 UNPACKING THE IP250D

The IP250D VoIP network terminal package contains several components:

•The main base unit, sometimes referred to as the keyset

•A handset for use during conversations

•A desk/wall mount bracket, to support the keyset at a convenient angle on the desk, or for mounting the phone on a vertical surface, such as a wall

•A network patch cable for connecting the keyset to the network

•A handset coil cord, to connect the handset to the keyset

•Package may also contain an optional power supply (if necessary)

2.3CONNECTING THE HANDSET

Plug one end of the coil cord into the RJ-10 receptacle on the handset and the other end into the receptacle on the left front side of the keyset. Place the handset into the cradle of the keyset.

2.4 CONNECTING THE IP250D TO THE NETWORK

Warning! Risk of electrical shock! Dangerous voltages may be present on the terminals of WARNING! the network patch cable after it is plugged into the network wall jack. Connect the patch

cable to the keyset base first, then to the network wall jack.

Plug one end of the network patch cable into the RJ-45 receptacle labeled 10/100 SW on the bottom of the IP250D keyset. Connect the other end of the cable to the network wall jack (receptacle) designated by the network administrator.

Caution: Do not connect a telephone cord to the network RJ-45 jack. A standard RJ-11 telephone cord connector can fit into the RJ-45 jack, however there is risk of damaging the equipment if this is done.

Note: The IP250D will not function until it has been configured and activated by the network administrator.

2.5 CONNECTING A PC TO THE IP250D

If the office or cubicle space has only one active network receptacle, and another network device such as a PC must share the same space, the PC should be disconnected from

the wall jack and reconnected to the RJ-45 receptacle on the bottom of the IP250D that is labeled 10/100 PC.

3 Teledex IP250D User’s Guide SIP/MGCP

Part Number 600-0480-60

Page 7 Page 9
Image 8
Page 7 Page 9
Contents IP250D VoIP Network TerminalImportant Safety Instructions Requirements of Part 15 FCC Rules European Requirements 89/336/EECContents Introduction to the IP250D VoIP Network Terminal Downloader Application Introduction to the Teledex IP250D VoIP Network Terminal IP250D Works Like a TelephoneInstalling the IP250D Connecting the Handset Connecting the IP250D to the NetworkConnecting a PC to the IP250D Unpacking the IP250DMounting the IP250D on a Wall Connecting a Headset to the IP250DArranging the IP250D on the Desk Configuring the IP250D HomeLAN Configuration Mgcp ConfigurationLAN Interface Settings Vlan SettingsMgcp Settings OOB Signalling SettingsSIP Settings SIP ConfigurationHandset Settings Codec Configuration System ConfigurationSecurity Settings Localization SettingsSnmp Settings Download ConfigurationReset Configuration Using the IP250D Telephone IdleIncoming Call Notification Receiving a CallPlacing a Call Headset and Speakerphone Usage Dtmf SignalingTerminating a Call Hold and Multiple Lines Teledex IP250D User’s Guide SIP/MGCP Muting a Call Transferring a CallRedialing the Last Number Dialed Forwarding ALL CallsUsing the Msgs KEY Configuring Local Speed Dial NumbersMaking Conference Calls Changing Ringing SoundsTroubleshooting and Care Basic Troubleshooting MeasuresGeneral Troubleshooting Network TroubleshootingSymptom MGCP-SPECIFIC Issues SIP-SPECIFIC IssuesCleaning the IP250D Using the Downloader ApplicationDownloader Application Executing the Downloader ApplicationDownload of the new firmware image Appendix B Safe Bootup ModesAppendix a Determining the IP Address Appendix C Restoring Factory Defaults ’SAFE’ Modes on AN IP PhoneAppendix D Dial Plans Sample Dial Plans Appendix E Tone and Ring Cadence ConfigurationTone Configuration Example Tone Configurations CUSTOM3 CUSTOM4 CUSTOM5 CUSTOM6 CUSTOM7 CUSTOM8 CUSTOM9Ring Cadence Configuration Example Ring Cadence ConfigurationAppendix F IP250D Product Specifications Appendix G Product Support
Top Page Image Contents