Shenzhen High Power Tech H7920 Ground, Power Supply, Interface and cable connection, Pin, Rts

Page 11

Galaxy H7920 Mobile Router User Manual

Chapter 2: Installation

Connectors’ description:

COM: Serial port (RS-232/485), serial data port or console port.

RJ45: 10/100BaseT auto sense Ethernet interface.

DC: DC power supply interface (+5VDC, +7.5V~+24VDC optional, check the label before power on.)

RESET: Reset button, press and hold for 5 seconds to reset the Galaxy router back to its default factory configurations.

ANT: Antenna interface (SMA female), standard, vehicle antenna, directional antenna optional.

Click “Start” -> “System Tools” -> “Default Setting” to reset the Galaxy router back to its default factory configurations. If you have forgotten the login password, press and hold RESET button for 5 seconds.

The Galaxy router will be back to the factory default configurations if the RESET button is pressed up to 5 seconds.

Management webpage address: 192.168.8.1

Login name: admin, Password: hongdian

Interface and cable connection

COM – Serial Port

COM serial port is standard, DB9 (Female) RS-232(DCE) interface (RS-485 optional); it can be assigned to CONSOLE port or data port.

RS-232(DCE) connector PIN definition:

DB-9 connector (DCE-Female)

PIN

Signal

Description

Direction

Note

1

CD

Carrier Detect

--

 

2

RXD

Received Data

--

 

3

TXD

Transmitted Data

--

 

4

DTR

Data Terminal Ready

--

 

5

GND

Signal Ground

 

 

6

DSR

Data Set Ready

--

 

7

RTS

Request To Send

--

 

8

CTS

Clear To Send

--

 

9

RI

Ring Indicator

--

 

For CONSOLE mode, the PC serial port that connects the Galaxy router should be configured to 57600, 8, N, 1; and then you can start a Hypertext Terminal at the PC, type commands to manage Galaxy router.

Galaxy router has a feature of the dial-up backup routing. Customer can connect a dial-up modem to the router COM port. A special cable will be required. The detail cable wiring is showed at the below diagram.

Galaxy H7920 Mobile Router User Manual

Chapter 2: Installation

 

 

 

 

 

 

 

RS-232 Modem

RS-232 DB9 (Male)

RS-232 DB9 (Male)

 

 

 

 

 

 

 

 

 

CD

1

 

 

1

CD

 

 

 

 

 

RX

2

 

 

2

RX

 

 

TX

3

 

 

3

TX

 

 

DTR

4

 

 

4

DTR

 

 

GND

5

 

 

5

GND

 

 

 

 

 

DSR

6

 

 

6

DSR

 

 

RTS

7

 

 

7

RTS

 

 

CTS

8

 

 

8

CTS

 

 

RING

9

 

 

9

RING

 

 

 

 

 

 

 

 

 

RJ45 – Ethernet

It is standard 10/100BaseT Ethernet interface (Auto sense).

DC – Power

DC power supply interface (+5VDC, +7.5V~+24VDC optional, check the label before power on.)

The power adapter output current should be not less 2A; Power supply ripple should be less 300mV.

ANT - Antenna

Standard 5OΩ/SMA RF connector (Female)

For outdoor use, lightning should be considered. We propose to install an arrester between antenna and the ANT interface.

2.4 Ground

To ensure a safe, stable and reliable Galaxy mobile router operation, DTU cabinet should be grounded properly. Connect the Galaxy mobile router cabinet to site ground wire.

2.5 Power Supply

Galaxy router is designed with advanced power management technologies; it can operate standalone. The input DC power voltage is +5VDC (+7.5V~+24VDC optional). You should check the Galaxy router label before power on.

The power adapter output current should be not less 2A; Power supply ripple should be less 300mV.

M80-792001-01

11

M80-792001-01

12

Image 11
Contents Galaxy Mobile Router H7920 Galaxy Mobile Router Abbreviations RSC Contents General System FeaturesSIM/UIM SpecificationsTypical Applications Application 4 Mobile Network/PSTN backup Open Box InstallationInstallation and Cable Connection Types DescriptionPanels MeasurementPIN Power SupplyGround Interface and cable connectionConnection Router ConfigurationCheck the Mobile Network Before Configuration Setup your PC IP address Setup Correct Network SettingsWEB Mode ConfigurationsBefore Configuration Check your PC Settings Main Menu Online Help Console ModeRouter Status Router Clock Router AdministrationSystem Tools System Information Configuration ProfileRestart Network SettingNetwork Basic Setting System LogAPN Snmp Configuration Dhcp ConfigurationDynamic DNS Route ConfigurationNAT/NAPT Configuration Route Configuration Security ConfigurationDTU Setting Special SettingSerial Port Setting Backup Routing Operation ModeDTR GND DSR RTS CTS Ring CLI Firmware UpdateHongdian Products LogoffOperation Trouble ShootingOperation Instruction Panel IndicationCOM Port Setting Appendix 1 Hypertext Terminal SettingHost System Encoding Method Galaxy H7920 Firmware Update Tool Appendix 2 Firmware Update ToolAppendix 2 Firmware Update Tool