Unitech RS700 Regulatory Compliance Statements, FCC Caution, FCC Radiation Exposure Statement

Page 4

Regulatory Compliance Statements

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B dig- ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit that is different from the con- nected receiver.

Consult the dealer or an experienced radio/television technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be cohabited or operate in conjunction with any other antenna(s) or transmitter(s).

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncon- trolled environment. End users must follow the specific operating instructions for satis- fying RF exposure compliance. Please follow the operation instructions in this manual to main compliant with FCC RF exposure compliance requirements. This fixed RFID Terminal meets FCC RF exposure guidelines when used in fixed RFID operation.

RoHS Statement

This device conforms to RoHS (Reduction Of Hazardous Sub- stances) European Union regulations that set maximum concen- tration limits on hazardous materials used in electrical and electronic equipment.

ii

Image 4
Contents RS700 Smart Rfid Fixed Reader Page Preface About This ManualRegulatory Compliance Statements Federal Communication Commission Interference StatementFCC Caution FCC Radiation Exposure StatementBattery Charge Notice Battery NoticesStorage and Safety Notice Warranty Table of Contents Appendix a Getting Started FeaturesIntroducing the RS700 Package Contents Front Panel Tour of the RS700Component Description Top Panel Bottom PanelConnect Power Using the Hardware Installing Wi-Fi AntennaInstalling Rfid Antenna Optional Gpio Pin Assignment Using the Gpio InterfacePin Name Description Mounting the RS700 Performing a Hardware Reset Making Rfid Applications Using Smart-Reader ServerOpening Smart-Reader Server Installing the Srsrc Program Installing Microsoft .NET FrameworkControlling Smart-Reader Server Remotely Using the Smart-Reader Server Remote Control Configuring Antenna Port Defining Smart Reader Behavior Creating a New EC Spec Start //spec1starttrigger Stop //spec1stoptrigger Specifying Report CriteriaDefining the EC Spec Urnepcpatgid-96*.*.* to match any GID-96 tagSubscribing the EC Spec Redefining the Subscription Viewing Data Collection Report Connecting to BizTalk Server Using the Application Programming InterfaceViewing Server Log Making Rfid Applications Making Rfid Applications Check Add single device. Click Next Input the RS700s IP address and port number. Click Next Making Rfid Applications Making Rfid Applications Making Rfid Applications Connecting to Oracle Sensor Edge Server Click MyEdgeServer Click Change dispatcherMaking Rfid Applications Click Add new device Select Smart Reader Device Click MyEdgeServer → Groups → Default → RS700 Click Start all devices Connecting to a LAN Network Advanced SettingsObtaining an IP Address Advanced Settings Setting the System TimeSetting up Ethernet connection Connecting to a Wlan Network Advanced Settings Advanced Settings Managing your Wireless Profiles Advanced Settings Advanced Settings Establishing Terminal-PC Connection Installing Microsoft ActiveSyncAdditional Capabilities Connecting the terminal to Your Computer Using Microsoft ActiveSync to Exchange Files On the computer, click My Computer → Mobile Device folderUsing Remote Control Click Start → Programs → ActiveSync Remote DisplayTroubleshooting Problem SolutionSystem Specification Appendix aSupport Region Web site