Uniden BCT8 manual Hold/Resume, Channel Lockout, Restoring a Locked-out Channel in Hold Mode

Page 27

BCT8 8/13/03 5:14 PM Page 23

Hold/Resume

If you want to stop on a channel during scanning, press

HOLD/RESUME.

If you want to resume scanning, press HOLD/RESUME.

Direct channel access:

There are several ways to access a specific channel quickly.

1.Press HOLD/RESUME.

2.Using the keypad, enter the channel number.

3. Press HOLD/RESUME again.

Note: You can also use the PRV/HWY, or key instead of pressing HOLD/RESUME.

Channel Lockout

You can lockout any channel so it is not checked during normal scanning. You can also restore the channel to scanning when you wish.

Lockout in Hold Mode

1.Press HOLD/RESUME and enter the channel number by using the keypad, then press

HOLD/RESUME.

––– OR –––

1.Press HOLD/RESUME and enter the channel by using the or key.

2. Press L/O to lockout the channel. “L/O” appears on the display.

Lockout in Scanning Mode

If the scanner keeps stopping on a particular channel due to noise or frequent transmissions, you may want to keep that channel from scanning.

1.Wait until the scanner stops on the channel.

2.Then press L/O.

3.The scanner immediately resumes scanning because the locked out channel is no longer in the scanning sequence.

Lockout Tips Write down your locked-out channels and put in a convenient place in case you need to restore them.

Restoring a Locked-out Channel in Hold Mode

1.Press HOLD/RESUME and select the channel number you want to restore by using the keypad, the or key, then press HOLD/RESUME.

2.Press L/O to unlock the channel. The “L/O” disappears.

23

Image 27
Contents Page Precautions Contents BCT8 8/13/03 513 PM LTR Introduction8 9 Front and Rear Views1718 Icon DisplayTerminology What is Scanning?What is Searching? What is Trunk Tracking?BCT8 8/13/03 513 PM Feature Highlights Where to Obtain More Information Information on the InternetScanner.uniden.com Included with Your Scanner Package Optional AccessoriesConnecting the Antenna Plug Installing the BCT8For Home Use Desktop Installation For Mobile Use In-Car InstallationConnecting the Power Cord Installation for everyday use Mounting the Scanner in Your Vehicle Typical Mounting MethodsDC power Installation Applying Power for Vehicle InstallationListening Safely Applying Power Using Standard AC PowerConnecting an External Speaker Connecting the Clone CableTurn the Scanner On Scanning OverviewHow Squelch Works Setting the SquelchHighway Patrol Scanning Selecting the StateScanning Highway Patrol Frequency Muting the Alert Tone Alert Tone VolumeHighway Patrol Scan Hold Highway Warning AlertPriority Channels Alert Light AdjustmentStoring Highway Patrol Frequencies Skip FrequenciesFlorida Trunked Highway Frequency Private Bank Scanning Programming Frequencies into ChannelsDeleting a Stored Frequency Duplicate Frequency Alert Memory LockScanning Private Bank Restoring a Locked-out Channel in Hold Mode Hold/ResumeChannel Lockout Restoring All Locked-out Channels Priority ScanChanging the Priority Channel Service Scanning Band Search Setting a Search BandSearch Hold Feature Data SkipFrequency Skip Storing Search Frequencies DelayTrunk Tracking Selecting Trunking System Type Programming Trunking FrequenciesProgramming Talk Group ID/Scan Lists Programming Trunking FrequenciesTo enter a Partial Edacs ID To enter a Type 2 Talk Group IDTo enter a Type 1 ID To enter a Full Edacs IDReceiving Trunked Systems ID Scan ModeID Scan Hold Feature ID Search ModeTo directly access a specific ID location Deleting a Stored ID ID Monitor ModeID Search Hold and Direct Entry ID in Hold Mode Programming Scan Lists During SearchReview ID Lockout To restore a single ID, follow these stepsTo restore all locked out IDs in a bank once ID LockoutMoving between Scan List Memories Setting the Delay Mode for Trunking ModeSetting Priority in Trunking Mode Trunking Frequency ConfirmationMulti-Track Operational Details Multi-TrackEdacs Reception Edacs TrackingProgramming Edacs System Frequencies An Edacs Trunked system AFS Partial Entry Feature Special Edacs FeaturesLTR Tracking LTR ReceptionMotorola Tracking Motorola ReceptionSelecting Preset Fleet Map Fleet Map ProgrammingProgramming a User Fleet Map Programming a Hybrid System Toggling the Status Bit Control Channel Only ModeDisconnect Tone Detect Option End Code To program your scanner PC Control ModeRemote Interface To connect Scanner to PCClone Mode Start Remote Mode and Change Transfer SpeedScanner.uniden.com PC Control Parameter To connect the Scanner to Scanner Send data Receive data General Use Care and MaintenanceTroubleshooting BCT8 8/13/03 514 PM Specifications State Cord Order AppendixPreset Fleet Maps Size Code Type I Programming Information User Defined Fleet MapsFleet Map Size Codes Uniden America Corporation One Year Limited Warranty