Uniden BCT8 manual Toggling the Status Bit, Control Channel Only Mode

Page 50

BCT8 8/13/03 5:14 PM Page 46

9. Use the keypad to enter a new Offset Channel, then press E.

Notes:• You can only input within a range of 380-759.

• If the system is not tracking properly, you may need to

try a new Base Frequency or Offset Channel, or you may be missing frequencies from the system.

You can set up to three Base, Spacing and Offsets for Motorola VHF/UHF trunked systems.

Toggling the Status Bit

On Type II trunking systems there is a method by which specialized types of communications utilize unique talkgroup numbers. An emergency call will occur on a unique talkgroup from its primary assignment, for example. Because the BCT8 defaults to Status-Bit ON mode, you never need to worry about missing these transmissions. If you have programmed talkgroup 33264 into Scan List memory, for example, and there is an emergency call within the group, you will hear it on 33264.

The only time you may wish to turn Status Bits OFF is if you're trying to figure out the proper Fleet Map of a Type I trunking system.

1. Press and hold TRUNK for 1.5 seconds and select the bank you want to change.

2. Use the or key to select

(Motorola TYPE2 800MHz),

(Motorola Type2

VHF) or

(Motorola Type2 UHF), then press E.

 

3. Use the or key to select , then press E.

3.Use the or key to select or , then press E. The scanner returns to Status Bit list item.

Control Channel Only Mode

When this function is activated, trunking is performed using Control Channel data only. Voice channel (also known as "DATA channel") frequencies do not have to be programmed into memory. This feature only applies to Motorola 800 MHz systems.

1.Press and hold TRUNK for 1.5 seconds and select the bank you want to change.

2.Use the or key to select (Motorola Type2 800MHz) or (Motorola Type1 800 MHz), then press E.

3.Use the or key to select , then press E.

4. Use the or key to select a plan from 4 frequency plans, then press E. The scanner returns to Control Channel Only list item.

Note: You must choose a plan before you begin to Control Channel Trunk (Only when 800

MHz system is selected).

 

When you deselect Control Channel only mode,

appears on the display.

Read the descriptions of the Plan 1~4 for details on which may apply for you.

46

Image 50
Contents Page Precautions Contents BCT8 8/13/03 513 PM Introduction LTRFront and Rear Views 8 9Icon Display 1718What is Trunk Tracking? What is Scanning?What is Searching? TerminologyBCT8 8/13/03 513 PM Feature Highlights Scanner.uniden.com Where to Obtain More InformationInformation on the Internet Optional Accessories Included with Your Scanner PackageFor Mobile Use In-Car Installation Installing the BCT8For Home Use Desktop Installation Connecting the Antenna PlugConnecting the Power Cord Installation for everyday use Typical Mounting Methods Mounting the Scanner in Your VehicleApplying Power for Vehicle Installation DC power InstallationConnecting the Clone Cable Applying Power Using Standard AC PowerConnecting an External Speaker Listening SafelyScanning Overview Turn the Scanner OnSetting the Squelch How Squelch WorksScanning Highway Patrol Frequency Highway Patrol ScanningSelecting the State Highway Warning Alert Alert Tone VolumeHighway Patrol Scan Hold Muting the Alert ToneSkip Frequencies Alert Light AdjustmentStoring Highway Patrol Frequencies Priority ChannelsFlorida Trunked Highway Frequency Deleting a Stored Frequency Private Bank ScanningProgramming Frequencies into Channels Scanning Private Bank Duplicate Frequency AlertMemory Lock Channel Lockout Restoring a Locked-out Channel in Hold ModeHold/Resume Changing the Priority Channel Restoring All Locked-out ChannelsPriority Scan Service Scanning Setting a Search Band Band SearchFrequency Skip Search Hold FeatureData Skip Delay Storing Search FrequenciesTrunk Tracking Programming Trunking Frequencies Selecting Trunking System TypeProgramming Trunking Frequencies Programming Talk Group ID/Scan ListsTo enter a Full Edacs ID To enter a Type 2 Talk Group IDTo enter a Type 1 ID To enter a Partial Edacs IDID Scan Mode Receiving Trunked SystemsTo directly access a specific ID location ID Scan Hold FeatureID Search Mode Programming Scan Lists During Search ID Monitor ModeID Search Hold and Direct Entry ID in Hold Mode Deleting a Stored IDID Lockout To restore a single ID, follow these stepsTo restore all locked out IDs in a bank once Review ID LockoutTrunking Frequency Confirmation Setting the Delay Mode for Trunking ModeSetting Priority in Trunking Mode Moving between Scan List MemoriesMulti-Track Multi-Track Operational DetailsProgramming Edacs System Frequencies Edacs ReceptionEdacs Tracking An Edacs Trunked system Special Edacs Features AFS Partial Entry FeatureLTR Reception LTR TrackingMotorola Reception Motorola TrackingProgramming a User Fleet Map Selecting Preset Fleet MapFleet Map Programming Programming a Hybrid System Control Channel Only Mode Toggling the Status BitDisconnect Tone Detect Option End Code To connect Scanner to PC PC Control ModeRemote Interface To program your scannerScanner.uniden.com PC Control Parameter Clone ModeStart Remote Mode and Change Transfer Speed To connect the Scanner to Scanner Send data Receive data Care and Maintenance General UseTroubleshooting BCT8 8/13/03 514 PM Specifications Appendix State Cord OrderPreset Fleet Maps Size Code User Defined Fleet Maps Type I Programming InformationFleet Map Size Codes One Year Limited Warranty Uniden America Corporation