XiNCOM XC-DPG602 manual Configuring for Internet Access, Settings Primary Setup Connection Mode

Page 13

Configuring for Internet Access

Figure 5. Primary Setup Screen

Select Primary Setup from the menu.

1.Configure WAN 1 and/or WAN 2 as required.

2.For any of the following situations, refer to Chapter 3: Advanced Port Setup for any further configuration which may be required such as:

Using both ports

Multiple IP addresses on either port

Multiple PPPoE sessions

PPTP connection method

Settings - Primary Setup

Connection Mode

Select the appropriate setting:

 

Enable – Select this if you have connected a broadband modem to this port.

 

Disable – Select this if there is no broadband modem connected to this port.

 

Backup – Select Enable for the primary port, and Backup for the secondary port. The Backup port will only be used if the primary port fails.

Connection Type

Check the requirements supplied by your ISP, and select the appropriate option.

Static IP – Select this if your ISP has provided a Fixed or Static IP address. Then enter the data into the Address Info fields.

Dynamic IP – Select this if your ISP provides an IP address automatically, when you connect. You can ignore the Address Info fields.

PPPoE – Select this if your ISP uses this method (PPPoE software that is usually provided by your ISP is not required to be used when selecting this method). If this method is selected, you must complete the PPPoE dialup fields.

Note: If using the PPTP connection method, select Static IP or Dynamic IP to correspond to the IP address method used by your ISP.

Address Info

This is for Static IP users only. Enter the address information provided by your ISP. If your ISP provided multiple IP address, you can use the Multi-DMZ screen to

 

assign the additional IP addresses.

PPPoE / PPTP Dialup This is for PPPoE and PPTP users only.

 

• Enter the Username and Password provided by your ISP.

 

• If using PPTP, enable the PPTP Connection checkbox and enter the IP address of the PPTP server.

 

• Host name (Optional For PPPoE) - This field is used by a Host to uniquely associate an access concentrator to a particular Host request.

 

Note: There are additional PPPoE/PPTP options on the Port Options screen. To use multiple PPPoE sessions on either port, configure the Advanced PPPoE screen.

DNS

If using a Fixed IP address, you MUST enter at least 1 DNS address. If using Dynamic IP or PPPoE, the DNS information is optional.

Optional

Host name – This is required by some ISPs. If your ISP provided a Host Name, enter it here. Otherwise, you can use the default value.

 

Domain name – This is required by some ISPs. If your ISP provided a Domain Name, enter it here. Otherwise, you can use the default value.

 

MAC address – Some ISP’s record your MAC address (also called “Physical address” or “Network Adapter address”).

Setup of the XC-DPG602 is now complete. PCs on your LAN must now be configured. See the following section for details.

13

Image 13
Contents Twin WAN DNS IP Gateway Table of Contents QoS Configuration DNS Configuration Use TWO ISPs for expanded bandwidth and redundancy IntroductionFeatures Password Protected Configuration Easy SetupHttp Firmware Upgrade and backup Dhcp Server SupportSystem Physical DetailsLED Action Condition Default SettingsOverview Basic SetupProcedure Configuring the XC-DPG602 for your LANNo Response? Configuring the XC-DPG602 for your LAN Installation Diagram for XC-DPG602 Connecting two broadband modemsSettings Primary Setup Connection Mode Configuring for Internet AccessConnection Type Address InfoTCP/IP Settings Configure PCs on your LANInternet Access OverviewFor Linux Clients For Apple ClientsFixed IP Address To act as a Dhcp Client recommendedAdvanced Port Port Options Health Check Auto Dialup Bridge ModeLoad Balance Settings Load BalanceAdvanced PPPoE Settings Advanced PPPoEAdvanced Pptp Settings Advanced PptpAdvanced Setup Host IP Host IPVirtual Servers Virtual ServersCustom Virtual Servers Settings Custom Virtual ServersCustom Virtual Servers Server ListSpecial Applications Settings Special ApplicationsSpecial Application Settings Dynamic DNS To use the Dynamic DNS FeatureDynamic DNS Dynamic DNSFor Dynamic IP Multi DMZ & UPnPSelect the desired WAN port Private IP AddressAdvanced Features Advanced FeaturesSettings Advanced Features HTTP// Internet IP Address of the XC-DPG602 Using Remote Web-based SetupFirewall Exception Security ManagementBlock URL Access FilterBlock URL Session Limit Session Limit & Firewall ExceptionQoS Configuration Configure DNS DNS ConfigurationXC-DPG602 & 603 Gateways How it worksDomain Name Configuration Public WAN 1 & 2 IP Address NS Record Primary/Secondary Name ServerMX Record Mail Exchange Preference 1Record Map Host URLCname Record Host URL ListSnmp Simple Network Management Protocol Management AssistantEmail Alert System InformationSyslog Management AssistantSyslog Configuration Message StatusUpgrade Firmware Admin Password ScreenUsing the Tftp Utility Recommended Updating the Firmware Backup your configurationUploading the Firmware Http Upgrade FirmwareTo upload the firmware to the router Restoring Saved ConfigurationOperation & Status Overview Operation & StatusSystem Status Operation & Status Restore Factory DefaultsWAN Status NAT StatusExisting Dhcp Server Advanced LAN ConfigurationStatic Routing Advanced LAN Configuration192.168.2.0 Configuring other Routers on you LAN255.255.255.0 192.168.1.100Operating Temperature DimensionsStorage Temperature External Power AdapterChecking TCP/IP Settings Windows 9x/ME TCP/IP SettingsUsing Dhcp Using Specify an IP AddressUsing a fixed IP Address Use the following IP Address Checking TCP/IP Settings WindowsFigure G. Network Configuration Windows XP Checking TCP/IP Settings Windows XPOverview Troubleshooting
Related manuals
Manual 52 pages 60.23 Kb