XiNCOM XC-DPG602 manual Uploading the Firmware, To upload the ﬁrmware to the router

Page 42

Management Assistant

Example of how to conﬁgure to save ﬁle.

Uploading the Firmware

Using the TFTP utility you are able to update the ﬁrmware on the XC-DPG602, this is useful when you also need to recover the router from a crash.

To upload the ﬁrmware to the router:

1.Open the TFTP utility by double-clicking on it.

2.Enter the routers IP address (Default is: 192.168.1.1)

3.Click the Browse button and select the ﬁrmware ﬁle.

4.Click the Download button. It could take up to 1 to 3 minutes to upload the ﬁrmware, after which the router will reboot.

Example of how to conﬁgure to upload ﬁrmware.

Restoring Saved Conﬁguration

Once you have updated your ﬁrmware you are able to upload previously saved conﬁguration.

To upload previously saved conﬁguration:

1.Open the TFTP utility by double-clicking on it.

2.Enter the routers IP address (Default is: 192.168.1.1)

3.Click the Browse button and select the conﬁguration ﬁle.

4.Click the Download button. It could take up to 1 to 3 minutes to upload the conﬁguration, after which the router will reboot.

Example of how to conﬁgure to upload previously saved conﬁguration.

HTTP Upgrade Firmware

The Upgrade Firmware Screen within the XC-DPG602’s setup console allows you to upgrade ﬁrmware or backup system conﬁguration by using HTTP upgrade.

You can backup your system conﬁguration by press “save” button of Save System Conﬁguration. It will save the system conﬁguration for you. (Notice: You have to refresh the browser after you saved the system conﬁguration ﬁle)

You also can do ﬁrmware upgrade by input the correct password and the ﬁle name of your ﬁrmware. Remember do not Reset or Restart the device while update new ﬁrmware, because it may cause system to crash.

42

Image 42

Contents Twin WAN DNS IP Gateway Table of Contents QoS Conﬁguration DNS Conﬁguration Introduction Use TWO ISPs for expanded bandwidth and redundancyFeatures Http Firmware Upgrade and backup Easy SetupPassword Protected Conﬁguration Dhcp Server SupportPhysical Details SystemDefault Settings LED Action ConditionBasic Setup OverviewConfiguring the XC-DPG602 for your LAN ProcedureNo Response? Configuring the XC-DPG602 for your LAN Connecting two broadband modems Installation Diagram for XC-DPG602Connection Type Configuring for Internet AccessSettings Primary Setup Connection Mode Address InfoInternet Access Configure PCs on your LANTCP/IP Settings OverviewFixed IP Address For Apple ClientsFor Linux Clients To act as a Dhcp Client recommendedAdvanced Port Health Check Auto Dialup Bridge Mode Port OptionsSettings Load Balance Load BalanceSettings Advanced PPPoE Advanced PPPoESettings Advanced Pptp Advanced PptpAdvanced Setup Host IP Host IPVirtual Servers Virtual ServersCustom Virtual Servers Settings Custom Virtual ServersCustom Virtual Servers Server ListSettings Special Applications Special ApplicationsSpecial Application Dynamic DNS To use the Dynamic DNS FeatureSettings Dynamic DNS Dynamic DNSSelect the desired WAN port Multi DMZ & UPnPFor Dynamic IP Private IP AddressAdvanced Features Advanced FeaturesSettings Advanced Features Using Remote Web-based Setup HTTP// Internet IP Address of the XC-DPG602Security Management Firewall ExceptionAccess Filter Block URLBlock URL Session Limit & Firewall Exception Session LimitQoS Conﬁguration DNS Conﬁguration Conﬁgure DNSHow it works XC-DPG602 & 603 GatewaysDomain Name Configuration MX Record Mail Exchange NS Record Primary/Secondary Name ServerPublic WAN 1 & 2 IP Address Preference 1Cname Record Map Host URLRecord Host URL ListEmail Alert Management AssistantSnmp Simple Network Management Protocol System InformationSyslog Conﬁguration Management AssistantSyslog Message StatusUsing the Tftp Utility Recommended Admin Password ScreenUpgrade Firmware Updating the Firmware Backup your conﬁgurationTo upload the ﬁrmware to the router Http Upgrade FirmwareUploading the Firmware Restoring Saved ConﬁgurationOperation & Status Operation & Status OverviewSystem Status WAN Status Restore Factory DefaultsOperation & Status NAT StatusAdvanced LAN Conﬁguration Existing Dhcp ServerAdvanced LAN Configuration Static Routing255.255.255.0 Conﬁguring other Routers on you LAN192.168.2.0 192.168.1.100Storage Temperature DimensionsOperating Temperature External Power AdapterUsing Dhcp TCP/IP SettingsChecking TCP/IP Settings Windows 9x/ME Using Specify an IP AddressChecking TCP/IP Settings Windows Using a ﬁxed IP Address Use the following IP AddressChecking TCP/IP Settings Windows XP Figure G. Network Conﬁguration Windows XPTroubleshooting Overview

Related manuals

Manual 52 pages 60.23 Kb