XiNCOM XC-DPG602 manual For Apple Clients, For Linux Clients, Fixed IP Address

Page 15

Configure PCs on your LAN

For Apple Clients

1.Open the TCP/IP Control Panel.

2.Select Ethernet from the Connect via pop-up menu.

3.Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field can be left blank.

4.Close the TCP/IP panel, saving your settings.

Note: If using manually assigned IP addresses instead of DHCP, the required changes are:

Set the Router Address field to the XC-DPG02’s IP Address.

Ensure your DNS settings are correct.

For Linux Clients

To access the Internet via the XC-DPG602, it is only necessary to set the XC-DPG602 as the “Gateway” and ensure your Name Server settings are correct. Make sure you are logged in as “root” before attempting any changes.

Fixed IP Address

By default, most Unix installations use a fixed IP Address. If you wish to continue using a fixed IP Address, make the following changes to your configuration.

Set your Default Gateway to the IP Address of the XC-DPG602. Ensure your DNS (Name server) settings are correct

To act as a DHCP Client (recommended):

The procedure below may vary according to your version of Linux and X -windows shell.

1.Start your X Windows client.

2.Select Control Panel - Network

3.Select the “Interface” entry for your Network card. Normally, this will be called “eth0”.

4.Click the Edit button, set the protocol to DHCP, and save this data.

5.To apply your changes use the Deactivate and Activate buttons, if available OR restart your system.

15

Image 15
Contents Twin WAN DNS IP Gateway Table of Contents QoS Configuration DNS Configuration Use TWO ISPs for expanded bandwidth and redundancy IntroductionFeatures Dhcp Server Support Easy SetupPassword Protected Configuration Http Firmware Upgrade and backupSystem Physical DetailsLED Action Condition Default SettingsOverview Basic SetupConfiguring the XC-DPG602 for your LAN ProcedureNo Response? Configuring the XC-DPG602 for your LAN Installation Diagram for XC-DPG602 Connecting two broadband modemsAddress Info Configuring for Internet AccessSettings Primary Setup Connection Mode Connection TypeOverview Configure PCs on your LANTCP/IP Settings Internet AccessTo act as a Dhcp Client recommended For Apple ClientsFor Linux Clients Fixed IP AddressAdvanced Port Port Options Health Check Auto Dialup Bridge ModeLoad Balance Settings Load BalanceAdvanced PPPoE Settings Advanced PPPoEAdvanced Pptp Settings Advanced PptpAdvanced Setup Host IP Host IPVirtual Servers Virtual ServersServer List Settings Custom Virtual ServersCustom Virtual Servers Custom Virtual ServersSettings Special Applications Special ApplicationsSpecial Application Dynamic DNS To use the Dynamic DNS FeatureSettings Dynamic DNS Dynamic DNSPrivate IP Address Multi DMZ & UPnPFor Dynamic IP Select the desired WAN portAdvanced Features Advanced FeaturesSettings Advanced Features HTTP// Internet IP Address of the XC-DPG602 Using Remote Web-based SetupFirewall Exception Security ManagementAccess Filter Block URLBlock URL Session Limit Session Limit & Firewall ExceptionQoS Configuration Configure DNS DNS ConfigurationXC-DPG602 & 603 Gateways How it worksDomain Name Configuration Preference 1 NS Record Primary/Secondary Name ServerPublic WAN 1 & 2 IP Address MX Record Mail ExchangeHost URL List Map Host URLRecord Cname RecordSystem Information Management AssistantSnmp Simple Network Management Protocol Email AlertMessage Status Management AssistantSyslog Syslog ConfigurationUpdating the Firmware Backup your configuration Admin Password ScreenUpgrade Firmware Using the Tftp Utility RecommendedRestoring Saved Configuration Http Upgrade FirmwareUploading the Firmware To upload the firmware to the routerOperation & Status Operation & Status OverviewSystem Status NAT Status Restore Factory DefaultsOperation & Status WAN StatusExisting Dhcp Server Advanced LAN ConfigurationStatic Routing Advanced LAN Configuration192.168.1.100 Configuring other Routers on you LAN192.168.2.0 255.255.255.0External Power Adapter DimensionsOperating Temperature Storage TemperatureUsing Specify an IP Address TCP/IP SettingsChecking TCP/IP Settings Windows 9x/ME Using DhcpUsing a fixed IP Address Use the following IP Address Checking TCP/IP Settings WindowsFigure G. Network Configuration Windows XP Checking TCP/IP Settings Windows XPOverview Troubleshooting
Related manuals
Manual 52 pages 60.23 Kb