Panasonic BT-LT900A manual Control

MAIN MENU

INPUT SELECT

Item	Setting	Description
FORMAT	AUTO	For selecting the signals whose input is to
	1080/60I	be accepted in the YPBPR mode and in the
	1080/50I	RGB mode.
	1080/30P	The signals can be set for each mode, and
	1080/25P	when the MODE item setting is switched
	1080/24P	from YPBPR to RGB or vice versa, the
	1080/24PsF	mode is automatically switched so that the
	1035/60I	signal format which has been set for the
	720/60P	mode now set is accepted.
	576/50I	AUTO:
	480/60P	All supported signals are accepted.
	480/60I	1080/60I:
		1080/60I or 1080/59.94I format signals
		are accepted.
		1080/50I:
		1080/50I format signals are accepted.
		1080/30P:
		1080/30P or 1080/29.97P format signals
		are accepted. (This setting takes effect
		only when YPBPR is selected.)
		1080/25P:
		1080/25P format signals are accepted.
		(This setting takes effect only when
		YPBPR is selected.)
		1080/24P:
		1080/24P or 1080/23.98P format signals
		are accepted. (This setting takes effect
		only when YPBPR is selected.)
		1080/24PsF:
		1080/24psF or 1080/23.98psF format
		signals are accepted. (This setting takes
		effect only when YPBPR is selected.)
		1035/60I:
		1035/60I or 1035/59.94I format signals
		are accepted. (This setting takes effect
		only when YPBPR is selected.)
		720/60P:
		720/60P or 720/59.94P format signals
		are accepted.
		576/50I:
		576/50I format signals are accepted.
		480/60P:
		480/60P format signals are accepted.
		480/60I:
		480/59.94I format signals are accepted.
COMPONENT	SMPTE	For selecting the input level of the Y/Pb/Pr
LEVEL	B75	signals.
		SMPTE: This is selected when the signals
		are to be output from an MII VTR.
		B75: This is selected when the signals
		are to be output from a Betacam
		VTR.
RGB-SYNC	G-ON	For switching the connector where the sync
	EXT	signal is to be accepted.
		G-ON:This is selected when the sync
		signal has been superimposed onto
		the G signal.
		EXT: The sync signal is accepted at the
		SYNC connector among the analog
		component/RGBS connectors.

CONTROL

Item	Setting		Description
CONTROL	LOCAL	For selecting where the operations are to
	REMOTE	be initiated.
		LOCAL: Only operations initiated from the
			main controls can be performed.
			Remote control operations cannot
			be performed.
		REMOTE: Remote control operations can be
			performed,	but no	operations
			initiated by the main controls can
			be performed although there are a
			few exceptions to this.
		<Notes>
		≥ When REMOTE has been selected, the
		“	” lock mark appears on the status
		display.
		≥ When REMOTE has been selected, only
		the settings of the CONTROL item and
		LOCALENABLE item on the CONTROL
		screen can be changed as menu
		operations.
LOCALENABLE	DIS.	For selecting whether to enable the input to
	INPUT	be switched to the main controls when
		REMOTE has been selected.
		DIS: When REMOTE has been selected,
			the input can no longer be switched
			to the main controls.
		INPUT:Even when		REMOTE	has been
			selected, the input can be switched
			to the main controls.
BACKLIGHT TIME		For displaying the total operation time of
		the backlight.

The underlined setting indicates the factory setting mode.

21