Panasonic BT-LT900A manual Video Config

MAIN MENU

VIDEO CONFIG

Item	Setting				Description
GAMMA SELECT	GPI	For setting the gamma mode.
	NORMAL	GPI:		This	is the	GPI setting.	For
	FILM			details, refer to “REMOTE
				specifications” (page 22).
		NORMAL: The			normal	gamma mode	is
				established.
		FILM: The film mode that supports the
				Varicam digital cine camera is
				established. The actual film mode
				setting can be changed using the
				FILM GAMMA item listed next.
FILM GAMMA	TYPE1	This enables TYPE1 or TYPE2 to be
	TYPE2	selected as the FILM setting for the
		GAMMA SELECT item.
		For the differences between TYPE1 and
		TYPE2, refer to the graph below showing
		the gamma characteristics curves.
			Luminance
					Input level
					Normal gamma characteristics
					TYPE1 characteristics
					TYPE2 characteristics
COLOR TEMP.	USER	For setting the color temperature.
	D93	USER: Any setting from 0 to 63 (equivalent
	D65			to a color temperature range from
	D56			3000 K to 9300 K) can be
				established.
		D93: This is equivalent to a color
				temperature of 9300 K.
		D65: This is equivalent to a color
				temperature of 6500 K.
		D56: This is equivalent to a color
				temperature of 5600 K.
		<Note>
		The color temperature can be set for each
		gamma mode (NORMAL, FILM).
SHARPNESS	HIGH	For setting the image sharpness.
MODE	LOW	HIGH: The images are accentuated with
				fine edges.
		LOW: The images are accentuated with
				thick edges.
		<Note>
		The sharpness can be set for VIDEO and
		all other input channels.

Item	Setting			Description
SHARPNESS H	0	For	setting the image sharpness in the
	:	horizontal direction.
	2
		This item enables two settings, one for the
	:
	30	VIDEO input signals and one for other
		signals, to be stored in the memory.
		<Notes>
		≥ While this item’s setting is selected, the
		only information displayed on the screen
		is this item which appears at the bottom
		left regardless of the MENU POSI setting
		selected on the OSD screen.
		≥ The sharpness can be set for VIDEO and
		all other input channels.
SHARPNESS V	0	For	setting the image sharpness in the
	:	vertical direction.
	2
		This item enables two settings, one for the
	:
	30	VIDEO input signals and one for other
		signals, to be stored in the memory.
		<Notes>
		≥ While this item’s setting is selected, the
		only information displayed on the screen
		is this item which appears at the bottom
		left regardless of the MENU POSI setting
		selected on the OSD screen.
		≥ The sharpness can be set for VIDEO and
		all other input channels.
I-P MODE	MODE2	For switching the IP conversion mode.
	MODE1	MODE2:		Movement compensation mode
		MODE1:		Normal mode
		<Note>
		This setting takes effect when progressive
		signals (1080/30P, 1080/25P, 1080/24P,
		720/60P or 480/60P) are input.
MONO	GPI	For selecting monochrome images.
	OFF	GPI:		This is the GPI setting. For details,
	ON			refer to “Concerning the REMOTE
				specifications” (page 22).
		OFF:		Normal images
		ON:		Monochrome images
		<Notes>
		≥ No adjustments are possible when RGB
		signals are input.
		≥ When ON has been selected as this
		item’s setting, the setting for the
		CHROMA image control is fixed at 0.
		When the setting is returned to OFF, the
		CHROMA setting prior to the change is
		restored.
SD ASPECT	GPI	For setting the aspect ratio of the SD
	16:9	signals.
	4:3	GPI :		This is the GPI setting. For details,
				refer to “REMOTE specifications”
				(page 22).
		16:9 : The images are displayed with a
				16:9 aspect ratio.
		4:3 :	The images are displayed with a 4:3
				aspect ratio.

The underlined setting indicates the factory setting mode.

18