Panasonic TQBJ0303-1 Care and Replacement Replacing the Lamp unit, JJLamp unit, ON-SCREEN Display

Page 50

Maintenance

Care and Replacement

Replacing the Lamp unit

JJAir filter

The air filter should be replaced when cleaning is ineffective and when replacing the lamp unit. A replacement air filter is provided with a replacement lamp unit (ET-LAB80). Contact an Authorised Service Centre for the optional air filter (TXFMZ01VKG7).

JJLamp unit

The lamp unit, ET-LAB80 is consumable and you must replace it regularly. It is recommended that a qualified technician carry the lamp unit replacement and consult with an Authorised Service Centre.

JJNote on lamp unit replacement

zzHandle the lamp unit with special care as it is a glass product. Dropping or giving it a shock may cause it to burst or to be damaged.

zzIf you wish to discard the used lamp, please contact your local authorities or dealer and ask for the correct method of disposal.

zzPrepare a Phillips-head screwdriver.

zzWhen replacing the lamp unit, be sure to hold it by the handle.

zzHold the lamp unit horizontally to prevent broken pieces from scattering. When the projector is mounted in the ceiling, do not work directly under the

projector or put your face close to the projector, and pull out the lamp horizontally.

Note

zzPrior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.

Remarks

zzDo not attempt replacement with an unauthorised lamp unit.

JJLamp unit replacement time

When the lamp is consumed, the brightness may decrease over time. 3 000 hours of use is the replacing time as a rough guide, and that might be shortened by the usage conditions, characteristics of the lamp unit or environmental conditions. You can find the duration of usage time by checking LAMP RUNTIME in the PROJECTOR SETUP menu. Do not use a lamp unit over 3 000 hours. Failure to observe this may result in explosion of the lamp.

 

ON-SCREEN DISPLAY

LAMP indicator

 

REPLACE LAMP

 

 

 

 

2 800 hours

Displays “REPLACE LAMP” on the upper left of the screen

 

for 30 seconds. If any button is pressed within 30 seconds,

 

 

the message disappears.

Illuminates red, even in the

3 000 hours

Displays “REPLACE LAMP” on the upper left of the screen,

standby mode.

and it will stay until you respond. The power is turned off

 

 

automatically in 10 minutes.

 

 

 

 

Remarks

zzThe guide time, 3 000 hours, is a rough estimate based on certain conditions and is not a guaranteed time.

50 - ENGLISH

Image 50
Contents PT-LB90E PT-LB78VE PT-LB75VE ImportantSafetySafetyNotice Notice Serial numberEnvironment care information for users in China Important Safety NoticeFor business users in the European Union Important Safety Notice Declaration of Conformity Declaration of Conformity DoCInformation Contents Maintenance ContentsSettings AppendixPrecautionswith regardwithtoregardsafety to safety Precautions with regard to safety Do not place the projector in extremely hot locations Do not put your weight on this projector„„Lens Focus Always disconnect all cables before mov- ing the projectorSecurity Cleaning and maintenance„„Take safety measures against fol- lowing incidents DisposalPrecautions with regard to safety Accessories TXFQB02VKJ2Read this first Jjinitial SettingRead this first JjlanguageJJTop and front view AboutYourYourProjectorProjectorProjector body JJControl panelJJTerminals About Your ProjectorBack and bottom view Front view About Your Projector Remote controlJJTop view Screen size and throw distance Setting upSetting up Setting on a desk/floor Setting up Projection methodFront leg adjusters and throwing angle Projecting from rear Using translucent screenConnectionsConnections Before connecting to the projectorConnecting example AV equipment Connections Connecting example Computers JJDirect power off function ConnectingJJDisconnecting JJDirect power on functionIndicator status Status Power Lock indicator statusPower indicator status Press the Power button Switching the projector on/off Switching on the projectorPress the Release button to unlock the Power button Connect the mains lead. ÆpageAudio Setting Switching the projector on/off Switching off the projectorPress the Power button again Projecting an image Selecting the input signalProjecting an image Positioning the imageCapturing an image Switching the input signalRemotecontrolcontrolope ationoperation Stopping the projection temporarilyControlling the volume of the speaker Setting up the image position automaticallyResetting to the factory default settings JJINDEX-WINDOW displayJJButton functions in digital zoom mode Press the Enter button Select OKMenu Navigation JJOperating procedureJJResetting to the factory default settings Navigating through the MenuMain menu ON-SCREEN MenuSub-menu JjpictureJjdisplay Option Jjprojector SetupPosition SecurityContrast Picture ModeColor Temperature BrightnessNoise Reduction Still ModeDaylight View TV-SYSTEMKeystone Clock PhaseRealtime Keystone ShiftPosition menu Over ScanAspect Jjthrough Frame LockJJS43 Language menu Language menuStartup Logo DISPLAYOPTIOPTIONmenu menuON-SCREEN Display Wide Mode Auto SetupSignal Search Sxga ModeOther Functions Projector Setup menuPROJECTOR Setup menu Lamp Power Projector Setup menuStandby Mode Lamp RuntimeAudio Setting Function ButtonChange Pattern Test PatternInitialize ALL Security menu PasswordPassword Change Text DisplayRemote Controller Menu Lock PasswordControl Device Setup Menu LockJjinput Password Jjstatus Jjwired LANJjwireless LAN Jjpassword ChangeLamp indicator Jjtemp indicatorBefore Care and Replacement Care and ReplacementCare and Replacement Cleaning the projectorJJLamp unit replacement time Care and Replacement Replacing the Lamp unitJJNote on lamp unit replacement JJLamp unitJJLamp replacement procedure Lamp runtime is reset to TroubleshootingTroubleshooting TechnicalInformatiInformation List of compatible signals This projector can project the following image signalsTechnical Information Serial terminal JJPin assignments and signal namesJJCommunication settings JJConnectionTechnical Information Cable specificationsControl commands LAN terminalComputer Audio SpecificationsSpecificationsComputer PT-LB90NTE Ceiling mount bracket safeguardsSpecifications Index IndexUnit mm DimensionsTrademark acknowledgements