Panasonic PT-FW100NTU manual Position menu

Page 32

POSITION menu

Settings

Remote control

Control panel

See “Navigating through the MENU” on page 27. See “Main menu and Sub-menu” on page 28.

KEYSTONE

If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, you can correct keystone.

Image

Operation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE:

•You can correct the distortion ± 30 degrees from the plane. For a better quality image, installing the projector with a minimum of distortion is recommended.

•Some distortion may be retained for lens shift adjustment.

•The distortion of the Main menu screen is not correctable.

•The result of the keystone correction will affect the aspect ratio and the size of the image.

POSITION

NOTE:

•If the projecting signal’s dot clock frequency is higher than 108 MHz, the adjustment may not make a difference.

•DOT CLOCK needs to be adjusted before adjusting the

CLOCK PHASE.

CLOCK PHASE

If you require further adjustment for the same reason as the DOT CLOCK adjustment, you can fine adjust the timing of the clock. Press I H to adjust. (Available with signals from COMPUTER/COMPONENT only)

NOTE:

•If the projecting signal’s dot clock frequency is higher than 108 MHz, the adjustment may not make a difference.

ASPECT

You can switch the aspect ratio manually when needed. Press I H to cycle through the options.

Aspect ratio options

AUTO

Signals which contains an identifying signal will be detected and automatically project the image in proper ratio.

4:3

When a 4:3 or 5:4 signal is detected, the image will be projected without any change, and other signals will be adjusted to 4:3 with preserving original ratio.

You can move the projected image for fine adjustment. Press I H to move horizontally and F G vertically. (Available with VIDEO/S-VIDEO/COMPUTER/ COMPONENT signals only)

POSITION

H

 

V

DOT CLOCK

If you have interference patterns of the projected image, which is sometimes referred to as moire or noise, you can minimize it by pressing I H to adjust the clock frequency. (Available with signals from COMPUTER only)

16:9

When a 16:10, 16:9 or 15:9 signal is detected, the image will be projected without any change, and other signals will be adjusted to 16:9.

ENGLISH - 32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model No. PT-FW100NTU PT-FW100NTU Important Safety NoticeImportant Information Important Safety Notice Declaration of ConformityTrade Name PanasonicContents Settings MaintenanceContents AppendixPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Use only the specified batteriesRemove the used batteries from the remote control promptly Do not put your weight on this projectorDo not mix old and new batteries Electric shocks can result if this is not doneAccessories Preparation Minimum required setting screenRead this first Remote control About Your ProjectorProjector body About Your ProjectorTop and front view Control panelOutput by menu operation About Your Projector Back and bottom viewComputer. Selectable for input Setting up Calculation methods for screen dimensionsScreen size and throw distance Getting StartedFront leg adjusters and throwing angle Setting upProjection method Mounting in the ceiling and projecting from frontAdjusting the Lens shift lever Lens shift and positioningHorizontal shift Vertical shiftWhen the projector position is fixed Setting up Projector location rangeWhen the screen position is fixed Connecting with computers ConnectionsBefore connection to the projector LAN terminalConnecting with AV equipment Connecting with Video IN/S-VIDEOConnecting with Component ConnectionsPower indicator Switching the projector on/offPower cord Switching on the projector Switching off the projectorSwitching the projector on/off Switch the Main Power on Press the Power buttonSelecting the input signal Projecting an imagePositioning the image Focus lever Zoom leverRemote control operation Setting up the image position automaticallyOperating range OperationSwitching the input signal Using the laser pointerResetting to the factory default settings Projecting an image in INDEX-WINDOW modeCapturing an image Stopping the projection temporaryEnlarging the centred area Controlling the volume of the speakerProjecting 2 images at a time Adjusting with the bar scale items Menu NavigationNavigating through the Menu Displaying the Main menuMain menu and Sub-menu Menu NavigationPassword Change Network Standby ContentsWEB Control Live Mode CUT Status Initialize 169 1610Picture menu For RGB signals Detailed SetupFor S-VIDEO/VIDEO signals Position menu Aspect ratio depend on signals Frame LockScreen Format menu OptionOption menu Power OFF Timer Auto SetupSignal Search Direct Power onTest Pattern HighlandClosed Caption Input Password Password ChangeSecurity menu Text DisplayNetwork menu, the following items are available Network menuItems in Network menu TEMP, Lamp and Filter Indicators Managing the indicated problemsLamp indicator Temp indicatorReplacing the ARF Auto Rolling Filter Care and ReplacementCleaning the projector Care and Replacement Resetting the Filter When to replace the Lamp unitReplacing the Lamp unit Before replacing the Lamp unitCeiling mount bracket safeguards Care and Replacement Replacement procedureInstalling the safety cable Removing and replacing the lamp unitTroubleshooting List of compatible signals Technical InformationQuality *2 Dots *1 KHz MHzSerial terminal Technical Information Cable specifications Control commandsComputer connection guidance ProjectorLamp switching Switching input SignalsInput signal Remote terminalSpecifications COMPONENT1 OUTAudio Computer AudioScreen size and throw distance for 169 aspect ratio Screen size and throw distance for 43 aspect ratioDimensions Trademark acknowledgementsUnit mm These Operating Instructions are printed on recycled paperIndex ALS Ambient Luminance Sensor ARF Auto Rolling FilterCalculation methods LeverIndex Mains leadNavigation buttons Screen sizeNuméro de série Avis important concernant la sécuritéImformation Importante Avis important concernant la sécurité Information ImportanteAvertissement AdvertenciaPrécautions de sécurité AvertissementMises EN Garde Précautions de sécuritéSinon cela peut causer des chocs électriques Utiliser uniquement les piles spécifiéesNe pas mélanger des piles usées et des piles neuves Précautions lors de lutilisation Précautions lors de linstallationPrécautions lors du transport Avant de remplacer le lUnité de la lampe Remplacement de lunité de la lampeDélai de remplacement de lUnité de la lampe Installation du câble de sécurité Protections du support de montage au plafondRetirer et remplacer la lampe De lUnité dePanasonic Projector Systems Company Technical Support
Top Page Image Contents